Search results for query: *

Umarex/Walther I find it interesting that some are shooting down umarex as junk but not walther. They merged together in June 2012.

S&W 916a Never heard of that model. On the left side of the frame should indicate the model. A three digit would indicate a second generation pistol. I have found that when it sticks the disconnect is causing the problem. By the way, I've owned, shot and traded/sold over 25 S&W pistols and...

300 Black Out You may have to go to a heavier buffer to slow down the action. The heavier the bullet the more pressure buildup is needed for the BCG to move fully to the rear with time for it to pickup the round from the magazine. The 300 BLK Out is very picky about gas tube length and wheter...

Beretta uppers You can find several on Ebay. Complete uppers or slides

P345 Magazine disconnect You can remove the magazine disconnect with out any adverse effects. Just remove the rear sight slowly and be prepared for possible springs to jump out. The disconnect are the parts up front (muzzle). If you already have a problem and want to keep the disconnect...

P345 The P345 is wider than a 1911 but is lighter than a standard one. It also a double/single action pistol. Some people don't care for the trigger (a little heavy on double action) I happen to love mine but I've put a lot of effort into it, Magna Ported, removed magazine disconnect...

P345 I have a P345, which though not perfect, does run with the high end 1911's. I've done extensive work to it. Magna-Port, Hi-Viz sights, Wolf reduced hammer spring, Wolf + 5% magazine springs, Wolf 15lb Recoil spring, Removed Magazine disconnect, Removed from grip checkering and replaced...

P345 Since they hit the market I've gone through four of them (I shoot and trade). They have always been reliable and accurate. My current one has been Magna-Ported, Front Hi-Viz Sight, Wolf extra power recoil spring and 5% extra power magazine spring, reduced power hammer spring and I removed...

cross draw holster if you need a cross draw try kirkpatrickleather.com it would be their texas cross draw about $72

pressing out sights all i do is lock the slide down in a machine vise on the drill press, invert a drill bit and press them out. i've done this on well over twenty pistols with no problems or damage.

Sig Pro 2340 It sounds like you have my pistol, with the exception of the sights(mine are about half gone). It's a great shooter, very accurate and very soft recoil. I also have the SP 2009 and love it just as much. I have no complaints.

black powder firearms After using your rifle make sure you clean it well with dish soap and hot water. heat it up after clean and oil it down. this must be done the same day its used. the best finish in the world wont hold up if you use gun oil to clean it.

tenton tool I have one and it works better installing a sight rather then removing one. Looking at the midway photo you can see a notch on the horizontal bar, thats used for removing the front sight. the pistol I was working on had an after market squared sight and was to tall to place it over...

One of the Rarest During the late 70's early 80's my assigned pistol was made by Singer. At the time I had no idea of it's value and it was banged around a lot. If I knew then what I know now, I think it would have gotten lost.

4506 one of the strongest 45's made. it's one of the very few that will handle the 45 super. $400 would be a very good price on one in good condition.

Gun Smith???? You need to find a different Gun Smith, if a Ruger doesn't work out of the box using factory ammo it needs to go back to the factory.

Beretta 92 I've owned several over the years (6) and currenty have two. They are high quality hand guns. Slide breakage was not a big issue (only on the internet) The Navy didn't like them and bought some Sigs, which also had some slide failures. Yes they are large and fairly heavy but are...

American Made??? Several "Name Brand" American guns are made in whole or part over seas. Made in the USA may mean assembled.

4506 If you win that 4506 on Gunbroker.com send me a message, I have a slide and barrel.

Kahr Go with ever which one is cheaper, Both pistols are of the CCW type and a half inch difference in barrell/slide length won't make a difference.