Search results for query: *

Thank you for all the reply's. I'm going to be loading Lee Key-way slugs as per the recommended supplied Data and #4 buck for home defense. A couple of us practice with falling steal target and that is what the #6 was/is for. In a couple months , when back surgery is thru , I will let you the...

Interesting Read on shotgun reloading. I have a Q? for any KNOWLEDGEABLE Shot shell re-loader, Given a safe listed Primer/Hull/ wad/powder combo , can the 1oz payload be varied without problems ( ie #6 shot , #8 shot , 1 oz slug, 1 oz #4 buck)? Reasons as to Why or Why not.

Check out "Lucky Gunner " self defense ammo tests. A lot of info on his sight!!!

Check out the Habitat resale stores in your area Used counter tops are cheap. Cut ,fit , and assemble as you want.

Crimp is dependent on case length. they all look good Could be a lighter but I wouldn't pull them for that . You can lighten them next time. Send em and see what you get!!!

I'm working on 16 lbs of WC-846 (?) which is milspec BL-C (2) and am using 25.5 grns nder 55 grn pills ( SP HP FMJ ) for range fodder works for me

I brush necks on .308 Roll on lube pad for body lube than every 3-4 case neck brush with nylon brush w/lube (RCBS Pad Lube) to help inside sizing. When done dry tumble with CC media to remove lube (1-2 hrs) . On .223/5.56 I ues one-shot and make sure i get it inside the neck (angle down spray)...

I have been lusting after a Ruger 10 mm GP-100 lately. Has anybody here have any experience with it? How does shoot? Full power house 10 mm loads? ..40 cal loads?

I've come to like the .35 bore 9mm , .38/.357 new to me .38 Colt short and had a 35 Remington Marlin that great woods gun

Usually use Unique for my loads with SPP but started working with a surplus powder WC-820 (AA-9) and I HAVE to use SPMP to get it to light

Yes I value the advice of those who have more knowledge than I and want to hear from any experienced wisdom holder . Sometimes i have a harder time getting into words exactly what I'm asking.

I think the question really is what is the relative "HOTNESS" between WSP , WSPM and WSR? Will a WSP be to "HOT" to sub for a WSPM or not "HOT" enough?

Have a recipe for AA#9 in .357 Mag that calls for magnum primers which in current climate are scarce to say the least. Is it a bad idea to use small rifle primers instead. I have tried regular small pistol primers and it was unacceptable . I'm using WC-820 powder that uses AA#9 data. I have...

No they aren't copper washed steel. I've only vibrated/dry tumbled with Walnut or corncob before so I have no experience with lemishine. what are "the number of things" that aren't good ?

Bought some .38 Spec brass at the gun show yesterday and some if it has a rose/copper hue to it. Ran it thru tumbler for couple of hours and there is a difinite difference in some of the case colors. itg doesnt matter as there are different head stamps affected. Does anybody know what cause...

I read on another board that the BR-5 is SW Auto/ Lovex d036 wish they would all follow the same nomenclature

I was looking at the 147 gr truncated cone (RBR) for the 9mm although i do have a variety of 124 gr on hand that i could use now that its been mentioned I was trying to stay with heavier bullets due to power levels and staying subsonic. Haven't decided on the .300 BLK weight yet but probably...

Embarking into new territory and looking for knowledge. Looking for powders to use in loading for suppressed 9mm and in .300 Blackout. So far only two powders I've come up with CFE Pistol and CFE BLK. What is anybody else using for suppressed loads. Side note I've been away from reloading...

I also add small strips of paper tape inside hopper to powder measure where it goes together for a snugger fit

My power measure pops occasionally due to bad alignment of powder funnel inside fix was to polish and bigger chamfer on case/funnel interface