Search results for query: *

  • Users: MFInc
  • Order by date
  1. MFInc

    10mm Auto & Fed 200 primers

    I just ran 50 SMP primered 10mm rounds. they all ran fine.
  2. MFInc

    9MM brass…any preference?

    As per most here, I've had great luck with Blazer,Win,Fed. Didn't have great luck with Ammo inc, or Agular as they were done after being shot 2 times. Some of the ammo inc was done after the first shot.
  3. MFInc

    Does 300AAC require a heavy crimp?

    The bullets are 130 gr Speer's no cannelure. Most all of current my bullets dont have a cannelure. But seeing how the bullets came out ugly, I may have another issue causing this. ugh.
  4. MFInc

    Does 300AAC require a heavy crimp?

    I may have mis stated, Im just using the sizing die, and not flaring. Perhaps saying the expander was flaring was wrong.
  5. MFInc

    Does 300AAC require a heavy crimp?

    Yea the AI ammo has a fine polish on it so no telling. I am using an RCBS FL die set for 300 AAC. Did not flare other than what is on the sizing die. I did trim with a WFT and chamfered them, not crazy though. The 2 that shot, those primers are flat and didnt move. I had them loaded with H110...
  6. MFInc

    Does 300AAC require a heavy crimp?

    Not trying to have one get stuck in the barrel? that's not good....
  7. MFInc

    Does 300AAC require a heavy crimp?

    Some of it is Converted LC brass, that I got from Ammo depot I think. It was not anealed from what I could tell. Some of the brass is factory 300BLK HS. Ammo inc and Aguilar I believe. both non anealed as well. the two rounds that held and shot were LC converted brass. A few of the bullets...
  8. MFInc

    Does 300AAC require a heavy crimp?

    I recently loaded 50 rounds of 300AAC. These is the first attempt to load this round. Been doing handgun charges for about 2 years now. Anyways went to the range a few weeks ago to test them. Loaded one, ejected it and checked OAL. it went form 2.005 to 2..013, so I tried another and another...
  9. MFInc

    How do I know if I swaged 5.56 correctly?

    I have a 300 aac case stuck on my decapp tool for the App 1st gen. not the first time either, BUT yes you will need to use a primer, could perhaps try with a used one if you dont have any., but then take it out again. thats what I did before potentially wasting a good one. I usually try and run...
  10. MFInc

    Trimming Auto Pistol Cases is Unnecessary & Waste of Time So That’s What I’m Doing

    I had to throw away about 100 once shot ammo inc 9mm brass as it was too long and too big in diameter after shooting once.... Sizing didnt help to them in spec, were out one way or the other... I measured and sorted all of my multi shot active 9mm brass after that,about 500 cases, some were bad...
  11. MFInc

    Neck Expanding Die for 300BLK needed?

    I failed too mention I'm currently going to be using already formed 300 brass shot by me. A mix of factory and converted brass. Not converting any 5.56 brass yet. Figured I needed to chamfer the cases anyway after trimming. But reading these replies I think I'm ready to go with the gear I have...
  12. MFInc

    Neck Expanding Die for 300BLK needed?

    I already have the RCBS FL die set. I've seen videos where they weren't used, and then read that a neck expander die is necessary for proper bullet seating with that cartrdige. TIA
  13. MFInc

    What do have waiting for you in the reloading room?

    I have a lot of brass to sort through and process, when i can get to actually doing something..
  14. MFInc

    .300 ACC Blackout Casing Question

    I have alot of already converted 300 brass, Just have to remove the crmp on most. I have more 5.56 brass than I will ever convert so still trying to decide what to do withthose, as I don't want to process all that. Hello Starline!
  15. MFInc

    Best barrel for a G20 bear loads?

    I was watching that video last night haha.
  16. MFInc

    true 10mm loads

    Following.....
  17. MFInc

    Best barrel for a G20 bear loads?

    I have contemplated the 6" barrel. I'm not really a fan of how long the slide is on those. or the 2-3 inches of barrel sticking out if you use the small frame 20 slide with it. I've seen a "tactical" length barrell that is like 5.1" but then I run into the hanging out thing unless i get the...
  18. MFInc

    How many primers is too many? I need help!!!

    lol, They are growing 200 per day lol...400 if I go in the morning, then change my clothes and go later in the day lol.
  19. MFInc

    Best barrel for a G20 bear loads?

    Yeah, what i've read so far the, the glock barrel doesnt like lead. Plus they seemed to tumble after at 50 yards after 200 grains from what I've saw so far. Reliability is my #1 concern. I do reload as well so I'm trying to avoid bulging my cases like my 23 did before I changed it's barrel. I...
  20. MFInc

    Best barrel for a G20 bear loads?

    I'm building a G20 clone and it's barrel time. I'm mainly building this for bear/hog protection and will be running underwood's or buffalo bullets when i venture into the forest. Lighter stuff and reloads other times. I've read some barrels have trouble feeding the 200+ grain lead bullets. I've...
Back
Top