Search results for query: *

All of my 6.5creeds are in AR's. Best factory loads have been Hornady 123a-max and set's. I haven't nailed down any bullet weights w/powders yet, but working with superformance and 3 if the 500 series powders for now.

Here's the 9mil ported core 5" and 4.25" version. The black threaded is an Apex and the ss is a storm lake. The Apex stays locked longer that the 2 factory and the SL barrels. The other 2 are my 10mils w/Timney's.

My experience with the m&p line have been very pleased! Couldn't ask for a better firearm in a poly! The only other poly firearms I have a glocks, fn and springfield. My 1st experience with 45acp was horrible as it was a 1911 with a plethora of issues. I'd been shooting a 629 in 44mag...

My next purchase is a 40 and barrel change to 357sig. I have 2 10mil and 1 9mil in the m&p line and can't say anything bad about any of them. Just was wondering if any have a full size 45 m&p?

It's funny how sizes of handguns are labeled as denoted by cartridge than can be a determining factor. Most label 4" compact, but s&w only labels the 9 4" as compact, but not the 10mm. So, technically I have only 1 compact as I don't care for comps, bubs and micros. Now the...

When mag length @ 2.800" contributes to cartridge failure along with slower twist barrels you can only change it to a faster twist and/or find a mag that can get you the longer lengths. BC's will diminish when going up in calibers within the same bullet weight (we all know), but bc might not...

Going thru some cartridge list I noticed the 30t/c. Being a collaboration of Hornady and Thompson Center makes sense on how the creed line came about. Using QL the 30t/c is a better option than 308win, especially for the mid to heavy bullets. If I had all the BS items and time to get/make...

not anymore than a 6.5wastemoore

30cal gas slow cost bullets that's usually in fmj's. I have fmj's in 30cal weights if 110, 123, 125, 150, 170 and 185. Primers are almost the cost (maybe half) of the cheaper 1's. Average cost to plink 300wm with (lets say) 70gr ~85 cents.

I don't remember what factory pull weight was on my sbl, but checked the cb model and it's @ 3.65# w/factory trigger parts. The sbl w/ranger point precision no-flop trigger, palo verde gunworks spring kit w/ plunger averages 1.78# (the gun in my avatar). Just relaying this info if you're...

What's the trigger pull like, average or lite?

Lots of makeup, but brakes clean 😂

I changed the triangle my self to an rpr and changed the springs also at that time. Pull weight before was ~5.5# then went down to ~2.5ish. I didn't do a safety delete as some do. Added a wwg bear proof extractor. All changes were made to the gun in my avatar.

Seems like other companies that offer knockoffs have had issues (not necessarily the same as you've experienced) and didn't have the strange charges for warrantee repairs.

What model of eaa

Case length vs coal will change pressures. How it changes (higher or lower with neck tension being equal) is by seating depth changing along with case length. If coal (example) 1.125" and case length .980 from known safe (even @ max psi) will decrease in psi due to less neck tension if the...

Is it an eaa USA to and from? If eaa is like this then I'll never buy any of their products. Hopefully this will get remedied without costing you money......even $20 is a joke! It wouldn't make sense in blue states, but wouldn't put it past them? Does your ffl agree with it or question...

I do sight radius by barrel length or what can fit on the handguard of 16" barrels and longer only. I do a 75-80% of length of barrel between sights total, not just on handguards. 16" = 12-12.8" 20" = 15- 16" 24" = 18- 19.2" I haven't seen any difference on full distance compared to my...

Exactly! Hard to beat either

The 3 versions of the r95's you can't go wrong with either!