Search results for query: *

  1. R

    Cylinder Bolt Issue on 1858 Remington

    I haven't seen an Italian bolt wing break yet, they don't seem to be tempered... Pry it out a bit and see what happens. (Not too much, as it can push and tilt the hammer enough to cause the hammer to drag on the frame.) A real Colt bolt is hard enough to break if pried...
  2. R

    size differences for 44 balls

    ball size A Pietta factory cylinder specs a .451 ball, I use .454 for the added tightness and sealing. The Uberti specs .454, and I found that marginal in some guns, especially if Hornady balls, which are not as round as Speer, I've had them roll out, or move under recoil. I prefer .457, as...
  3. R

    Calculating Twist Rate with Sabot?

    The twist rate not only depends upon the caliber, but more on the length of the bullet. The longer the bullet, the faster a twist required. Same reason you must spin a football to throw it, not necessary with a baseball.. Check to see what twist rate your chosen bullet uses when in the mother...
  4. R

    ASM 1851 conversion cylender replacement

    A gunsmith with the proper reamer can change the chamber to 44 Special, presuming the cylinder is long enough for the loaded cartridge. He needs a reamer that will cut for the rim as well, as the 44 Colt has a bit smaller diameter rim.. I have Open-tops, one is 44 Colt, the other is 44...
  5. R

    adding a front sight

    Do realize that the heat of silver soldering will remove the bluing. Brownells sells a low temperature (450 degree) gunsmith's "silver solder" that requires far less heat, and is extremely strong. Actually, the melting point of mid and high temp "real" silver solder id dangerously close to the...
  6. R

    Anomaly: 1849 Colt With Dragoon Barrel

    I don't think, even going past the flat diameter will weaken the barrel enough to be dangerous, there is a step in a dragoon barreled 36 Navy type (see Confederate) without harm. For that matter, there is a step in a Dragoon. The high pressure (such as it is) is in the cylinder, as...
  7. R

    What BP for use in flintlock and ball and cap pistols?

    Yes, BP subs don't work well in a flintlock, unless you create a duplex load, with BP at the flash hole. Also, the flash pan works best with 4fg powder. Cap & ball, 31 to 45 caliber are fine with 3fg, but in a flintlock or percussion single shot, if the caliber is over 50, best to use 2fg.
  8. R

    Pietta shooting too high? Easy fix.

    My easy fix is to install dovetail front sight..
  9. R

    Cartridge/ml pressure question

    The conversion cylinders by Howell/Tatlors or Kirst will take SAAMI loads. The frames are strong enough to take the recoil, though softer than the cartridge frames like the 71 Opentop and SAA, and factory Remington conversions, they will survive. The steel is a quantum leap over the original...
  10. R

    Remington Revolving Rifle

    I have an Uberti RRR, and with a conversion cylinder (Taylor/Howell or Kirst) it will clang a steel silhouette at 200 yards with no problem, with either black or smokeless powder in 45Colt.
  11. R

    Gain Twist in BP Revolvers

    The Uberti screws are metric, and very close to the Colt, and a tap for the Colt screw will clean yup the hole for the Colt screw. The Colt is a #8-36, and the Italian a M4X0.70. M4 dia is .157, #8 dia is .164. 0.70mm is 36.2 pitch in inches. The head on an M4 Uberti screw is 5mm (.197)...
  12. R

    Buttoning up the open tops

    If your arbor is too hard, use a carbide drill. There are also carbide center drills, to start your hole. Before using the Dillon button, I used to drill and tap the arbor for a set screw and the screw can be adjusted for the proper fit and locktite'd in place.
  13. R

    Buttoning up the open tops

    I tried the Dillon buttons used for the shell plate to retain cases in the reloading machine. (The trick was first posted by Larson Pettifogger) Drill a hole in the end of the arbor to accept the Dillon button, then adjust the thickness of the head with a file or lathe to get the barrel...
  14. R

    Buttoning up the open tops

    See next post
  15. R

    1858 conversion: need technical advice

    The short barreled guns have a lever latch as a slide fit in the dovetail, you can push it out with your fingers to remove the lever and get the pin out. The thing to watch for is that the latch stays in the dovetail when you're using the revolver. Shooters that have shortened the longer...
  16. R

    1860 Army Grip frame screw

    The mainspring is the same as the Navy, the gripframe is longer, but the location of the mainspring screw is the same distance down as the Navy. The screw at the toe of the gripframe is larger than the Navy or OpenTop. The part number at VTI gunparts is 455.
  17. R

    Thunder grip

    This is Uberti, but the Thunderer gripframe looks pretty good, particularly on a shortened revolver.
  18. R

    Fitting Cylinder on 1873 SAA

    When fitting a cartridge cylinder, check and adjust (if necessary) the headspace first and foremost, then the bushing. The cylinder gap will be whatever it becomes at that ploint.
  19. R

    1858 Conversion Cylinder

    As far as strength, the Uberti is pretty strong of frame. The 36 withstood factory Remington 45 Colt until the lead at the forcing cone stopped the rotation... Don't ask me how I know. And the resized bullets hit the target.
  20. R

    Uberti 1851 London Model

    The Uberti 51 Navy grip (brass) is slightly smaller than the SAA. The London, I read, uses the SAA steel grip frame, so it fills the hand a bit better. I don't know if this is true of the steel 61 Navy grip frame, it would make sense, but when has that ever counted for anything?
Back
Top