Search results for query: *

Went to sportsmans warehouse today to get some basic supplies. I was there two weeks ago and today found that Winchester primers had went up $6 a brick in two weeks. That's worse then fuel prices. I not a panic buying, but this trend concerns me. -Hardcorehunter5

Is the core-lokt bullet component made over seas like I suspect. The loaded ammo is made in the usa but what about the bullet itself. It is packaged by Black Hills Shooter Supply which makes me believe it is a non usa product.

This is not another opinion post, well at least not the typical one anyway. I was picking some NRA raffle tickets the other day and was directed to the gun case by the shop owner. He knows I'm a lefty and always tries to suck me into a purchase. Well anyhow it an A-Bolt .270 wsm, with a...

Just looking for the actual weight of the bare gun. Remington has rifle twist, barrel and all that BS but not weight on their website and I cant seem to find it anywhere else. Any ideas?

well since I get no sympathy at home, I thought I would post my dismay. my wife and I work different shifts and the dogs kennels needs repair, so when I leave for work I put the dogs in the master bedroom and she gets home about 1 1/2 to 2hrs. after me and everything is good. They have...

I was given a satndard model 60 as a "gift" from awhile back and it did not have a magazine tube. I purchase a new outer tube, inner tube, magazine band and band pin. when I place the band on the tube and install the drift in the band it compresses the tube so the inner will not move in or...

well gentlemen I hate to ask this question. Went to work today without looking at my manual as planned. I need to pick up some powder to load some .277cal nosler ballistic tips 130grains. I can't remember which powder they listed as most accurate, consistant and uniformed and there is no one...

I just bought a the bianchi tornado positive retention holster for my usp .45 fullsize. I am a left handed shooter, so the decocker is on the right side ofthe weapon. The snap on the holster is very difficult to secure with the decocker in that position. With the decocker set up for a righty...

Well there may be a simple solution to my question, and hopefully you all can help me out. When I use win296 for reloading .44 mag it is very difficult to get all the powder out of the dispenser when I am finished. So far I have had to completely disassemble the dispenser every time I use that...

Well I took some advice and started a new thread just on the 25-06. I was thinking about this round, wel just for fun. I would use it on deer in the long run. I also like thought of having something that is a little on he rare side. The only problem that I have is I am left-hand, so i...

I was looking at a catalog the other day and saw tht weaver and b-square offer scope mounts that attache to super blackhawks. Has anyone used them before and do you think it would be effective on a 5 1/2 barreled model. thanks

Well guys I just got my .338mag, but I have a problem. I don't know if I should buy factory ammo and save the brass or just buy brass and start reloading. I kinda don't want to have to trim the new brass. I can get factory ammo for about $21-25 a box. brass from midway is is close to $38...

I just bought a HK fullsize .45 today. I will be using it for police academy, then as a duty weapon. What is the over all opinion of the stock standard sights. I would like to put night sites on eventually. Any suggestion would be great!!

.338 win mag Well I got a new toy today at the cow palace gun show. Left-hand bdl in .338 win mag. It is used, but not very much. I couldn't believe the price, $449.00. I thought that was cheap for the condition of the gun. It was pretty clean. What do you guys think?? Can you rec. some...

well guys I am looking for a new tumbler and want something that is very quiet. I will use it mostly for rifle cartridges. I do not to spend and ton on a rock/gem tumbler. I was think more along the lines of a vibration style. So what do you guy use and what in the quiets. Noise level...