Search results for query: *

Bullseye

Use a shell holder in the hammer. My O ring wore out and I did not want to wait to get a replacment and read where a shell holder will work.

I was going to try the same thing. Speer manuals did have the information but people had to many feeding problems and speer discontinued publishing the information. My 115gr FMJ 9mm measures .579, length of bullet. My .380 95gr FMJ measures .446 = .133 or 1/16 of a inch difference or...

Go here and click on what you want to know. http://www.topglock.com/info/info.htm

I reload for the 380 95gr RN bullet FMJ. I bought some Magtech, but any will do Tite-group powder, Speer book #13 2.7-3.1, I used 2.9 Bullseye Speer book 3.0-3.3 I use 3.1 COL or AOL .970 Light taper crimp, just remove the bell. Shot in a T380 Bersa with no problem. Shot 500 so far...

I also use Lee neck sizing dies, for 30-06. After 10 rounds I FL resize and trim. When I trim there is very little metal taken off. The brass will grow some but very little. After 30 times using the brass I start over with new brass (just me) even though they still look OK.

I have a stoeger cougar. It is a fine gun. No problems. I only have 800 thru it so far. Shoots anything I put in it. Very accurate. G Cole

.234 Thanks for the info. Think I will go with the .243. Had a rem 6mm semi-auto back in the 70s, sure liked the way it shot, but used it only for deer.

I want to get a 10GXP3 in a .243, but have read the barrel life is bad. I just want to punch paper about 20 a week. I wanted somthing larger than the 22 and thought the .243 would be nice on recoil. I have a 30-06, 30-30 and 22LR and the 30-06 recoil is starting to wear on me as I just turned...

XD Mag I have both 9mm SC and .40 SC for CCW. I shoot both at the range using the small mag. I have never had any trouble in either gun.

Has anyone used the ATS sight? If so how did you like them? Are they as accurat as stock sights at 25 yards?

Thanks everyone for the replies. I do not shoot real good since I am one day older than dirt, but I do enjoy reloading, and want to do the best that I can. Walkalong I think I will get the sinclair # 09600 as it has the .224 cal which I would like to get next.

In San Antonio S.W. was almost out of power and primers 3 weeks ago. Last week they got a lot of powder and some primers in. They said the stuff was hard to find or get.

I am new to reloading for a rifle, and have a problem. I took a 30-06 case, full length resized and used a fine hack saw to cut one side of the neck, so I could measure free bore or bullet to lands. I checked the length of the bullets and they ran 1.105 to 1.112. They are Speer FMJ-BT 150gr I...

Thanks everyone on the fast replys. One more question. What is the twist rate of the.308 Or what is the heaviest bullet I can use.

Anyone have have a Saiga semi-auto rifle? I was thinking about getting one but know nothing about them. Are they accurate out to 300 yards Will they last

oal I set oal at 1.120. I will try the lighter powder load. My book said 4.0 to 4.7 so I went with 4.2. I found out about the FC brass and will use them one time only.

Powder Tite-Group Just bought some tite-group powder. I loaded some and they shot real good in my Glock22 and XD 40 SC. I had been using Bullseye, but this is much cleaner. I got a good group at 25 yards using a rest with Glock 22. 180gr berry's RS (round shoulder) 4.2 tite-group FC...

Just bought some tite-group powder. I loaded some and they shot real good in my Glock22 and XD 40 SC. I had been using Bullseye, but this is much cleaner. I got a good group at 25 yards using a rest with Glock 22. 180gr berry's RS (round shoulder) 4.2 tite-group FC brass CCI primers...

Thank You I want to thank you for the information on the big dot sights, the video was exclent. Geo