Search results for query: *

range brass at my club its required you sweep up your brass and keep it, or put it in one of the clubs 5 gallon pails, once in the pail you can take it. wood

low ceiling my ceiling is 77". real old house, anyway, the bench height is 35.5 and the height from the bench top is 44.5. with the 650 mounted directly to the bench i have plenty of room to remove or reassemble the casefeeder. I'm of the opinion you do not need the strong mount, just bolt...

powder and primers i recently 8 lbs of bullseye for $99, and 5000 lg pistol primers for $110. wood

similar situation I bought a press and had similar problems as stated earlier, fiddling, adjusting, breaking plastic parts, and not getting close to the suggested output per hour. The second time around i did a little more research and talked to more than a few reloaders and visited 2...

while we're on the subject I spoke to several folks in my area, one had bought a used Dillon only to find out he did not get all of the parts he thought he would. in this case you have to pay for those that are missing. wood

great move Congrats on buying your 650. I'm guessing that you did not get the case feeder.... I would highly recommend the casefeeder and powder check, over the handle and strong mount.... if you can afford it. these make life much simpler.... and you can reload instead of checking...

650 casefeeder I have a 650 with casefeeder, i have to guess its the same for the 550. I have had no issues with it at all, works as described. However if i was making this decision, i would sell the 550 and get a 650. there are 5 stations vs 4, and the price difference is not that much...

cost In the reloading section of GT there is a quickie formula to calcualte cost per round and per 1K... you'll save, unless your paying high prices for components. wood

for the future the best thing is to use the loading trays. when i started thats what i did, but this was the advise from 2 very experienced loaders. you can do it several ways: 1. run a flashlight over each round after you put powder in the 50 or so the tray holds. 2. you can use a...

cleaning primer pockets I don't clean them either. It would just take too much time. If i find 3 out of 100 with primers not seated properly i just toss them. If i were shooting a bullseye match, etc. and had matched brass etc that would be different i might consider cleaning them. wood

not quite clear I have a 650, both the Lee and Dillon used industry standard dies. You can buy Lee dies and use them in your Dillon. as for caliber conversion, the Lee obvioulsy will not work in the Dillon. Does this help. wood

Thanks all Thanks for all the info, from the replies above $170 seems high. But you gotta ask and get the info. In the end if no one wants it i can always leave it set up for one caliber. Thanks again, wood

almost correct philbo, are you referring to the reconditioned 1000's for $96 plus shipping then you correct. The Price for a new 1000 is $215.98 plus shipping. I doubt that LEE would ever undersell their distributors. wood

no i didn't mean $70 atomd.. i meant $170.00 you did not include 2 extra turrets 8 each (total of 3) $16 1 shellpalete carreir with 9mm shellplate, and primer flip tray . $36 1 38 cal shellplate...

price I am going to put it up for $170 plus the actual cost of shipping. Buyer chooses the carrier. I would of course accept any reasonable offer. Thanks for the help on this i appreciate it. wood

why am i selling I bought an xl650 with casefeeder. wood

how used?? I would guess about 1500 or less rounds thru it. w.

Purchased in May of 2007, I'm looking for opinions on what should i post as an asking price for the following: Lee pro 1K press with shellplate carrier large pistol 3 turrets 2 case coallators and feeders 45acp and 9mm Shellplate carrier small pistol 38 cal. shellplate auto disk update...

primers I am using CCI large pistol. wood

primers While we're on the subject of primers, i noticed that if i wait until the "low primer alarm" goes off to fill the primer, the next several rounds have no primers.... Anyone else have this problem\??????? W.