Search results for query: *

  1. S

    House Gun Opinion?

    I voted for the revolver. I am not a 1911 guy. Revolvers are stupid simple just point and keep pulling the trigger till it goes click.
  2. S

    Please help me choose a 40 cal. pistol ...

    I voted for the Glock, (I own a G23) but I would be hard pressed to pass on an M&P. They don't have the options like the Glock but they sure do shoot nice.
  3. S

    oversized grips for SP101

    I have the Hogue rubber ones on my SP101 and I would be hard pressed to find a better grip for me.
  4. S

    Any new revolvers rumored for 2013

    I wouldnt call new revolvers junk. But my S&W 19-2 is a lot nicer than my S&W 617. The same as my old model BH is nicer than my SP101. But they all shoot well and function flawlessly
  5. S

    Have a look at my petition

    All petitions need to get 150 signatures to go public. I know it is spitting in the wind but I had to do something. I already contacted congressman and senators.
  6. S

    White House petition

    I posted a link to another petition I made earlier today if your already registered might as well sign mine too if you agree with it. I need to get to 150 before it goes public.
  7. S

    Have a look at my petition

    Hello, I know it won't do a whole lot of good but, I have created a petition in response to all the closed mindedness I have see on both side of the gun control craziness as of late. The gun nazi's think that an ar15 was the cause of Sandy Hook and the NRA blamed it on video games like they...
  8. S

    glock bulged barrel ,just replace it???

    I agree, I have a few barrels for my Glock the factory barrel is the least accurate as any of them. But it is the one I keep in there for home protection.
  9. S

    caliber conversion question

    Like it has been said it isn't worth the trouble. I would like to have an old 32-20, I always like the S&W's better than the Colts.
  10. S

    Rust removal / treatment?

    Thats one way to do it. I use 0000 steel wool and some gun oil to get light surface rust off guns.
  11. S

    AR-15 From the ground up... any comments?

    I do agree putting an AR together isn't rocket science. That being said I didn't want to fool with putting the upper together, thats why I went with Del-Ton.
  12. S

    AR-15 From the ground up... any comments?

    I built mine for about 500 minus all the mags I bought. Compared to 1k I would say you save a little. You might just wait till the market totally drops out and prices drop.
  13. S

    DEL TON build kits

    I have a mid length kit and built it on a doublestar lower. The kit is just fine. There is just a hell of a wait. I am sure it is speeding up now. As far as tools go you just need the spanner for the stock. Del-ton assembles and test fires the uppers for you. It is worth it in my book. They are...
  14. S

    Can you cut and rethread an AR barrel ?

    Like RC Said you will need to open up the gas port to get more gas to cycle the action since it will have less time. I would just find out the size of the port with a sbr and open it up to that.
  15. S

    Can you cut and rethread an AR barrel ?

    You can cut it down no problem but I imagine you will need to resize your gas port to make up for the lack of the 5 inches of barrel length.
  16. S

    Suggest a mild 38 special load after carpal tunnel surgery?

    I shoot a 158 over 3 grains of red dot for my 38 loads but as far as least amount of recoil like it has been said I would find the lightest bullet you could get then go from there.
  17. S

    Glock-smithing

    I have a 22 that I have tried all kinds of stuff in. I finally settled on Lonewolf 3.5 connector with a stock spring. I tried stock glock 8,5, & 3.5 connectors with stock and NY springs. I liked the combo I have the best. I also went through and polished all the mating surfaces. I also added a...
  18. S

    ruger blackhawk

    Since you have that much money I would look into sending it to a smith good with blackhawks. I am sure you can do a search. I am broke so I do all my own work. I would find someone to slick up the trigger, check the timing, Check all the chambers for uniform size and ream if needed. You didn't...
  19. S

    Why I don't use Loctite on Mounts/Rings

    I use blue locktight and have never had a problem. What you should be telling people is don't use red or JB Weld. I picked up a Contender barrel once mainly for the fore end and the scope mount with the plans on selling the barrel for the price I paid for it. I had a lot of trouble getting the...
  20. S

    Which would you pick?

    Well a contender will set you back a lot less than a Colt. You have to pay for the pony. I have a Contender and and Encore. I use to have the Encore set up as a pistol but it was just too big. Now I just run the Contender as a pistol. My current calibers are 7-30 Waters, 357 Mag, .222. I have...
Back
Top