Search results for query: *

mine is a Stevens 200(its made by savage) cost me $400, then another $120 for a Redfield revenge 2-7x32, I love it, simple it works, basically a model 10 without the accutriger. um not really a fan of the axis myself, shot one in 30-06. and I got a special dislike for Remington. around hear you...

I was able to test fire it, I have some feed issues, hopefully a Lil polish will fix. I only got one round shot. but when I inspected my brass the case mouth got shaved down to a sharp taper, any ideas on what happened? I kinda think that because it didn't fully cycle the case got slammed back...

I've used it, but like frog lube better i

and maybe some Allen keys if it has a set screw in the bottom of the base, make sure your muzzle break ain't welded/pinned on

it is a striker fired system now, and in the event that the sear fails the striker "should" ride with the bolt and prevent slam fire, the firing pin does not protrude from the bolt with the strike fully seated seated on the bolt

it is not the sear itself, it is called a sear lever/trip leaver and it works like a disconnect, but when I charge it it holdsthe striker, but the trip lever doesn't disconnect, but the sear does release if I let off the trigger. m fcg is 100% original

ok, my trip lever is not engaging my bolt, how should I go about fixing it?

Thanks for the information, I did decide to go ahead and make it a 9mm. My reamer should be here tonight

you can also through that stock in a black trash bag and let it sweatout the cosmoline. I had a similar problem with the stock on a nagant. I ended up refinishing it with a really dark stain

indeed I do know a couple guys who have a lathe, and they are willing toto help me with the bolt and barrel. is im planning on making my bolt face.002-.003 larger then the diameter of the357sig base to start off with then making slow adjustments as needed. anyone know what to do as far as coming...

okay, my new bolt has a recessed bolt face, and I'll need to open it up a few thousandth to allow the 40casing to fit, is there a tool made specifically for opening up the face?

I have heard of 40s and 10mm stems. but I've not actually seen one. the bolt itself, with my conversion is also made to run the 7.62x25 and the 9mm. I checked a 40case to my bolt face. and it fits. my trunions will be riveted, and the mags will stack the 40. so I guess now its a matter of can I...

I'd sayout the muzzle... but that's just what I'd do

alright then. I'll stick with the 9mm. another question is if it would be safe to solder the trigger housing to the tube vs welding. based on my understanding the housing doesn't take a lot of pressure?

So I finally started buying my parts to build a stengun. im using a mark 3 parts Kit, and a Indianapolis ordinance semi auto conversion. I was wondering if anyone has information on calibers, specifically the 357 sig and weather or not it could safely work in a build like this. I see that the...

timney makes a trigger group for them

the way I see it, the m16, M&A, and ar platforms wouldn't have ever gotten the forward assist if there wasn't a real problem present, you may never actually need it, but your gonna hate not having it if youever do, its not like you can slap your charging handle to help the bolt seat properly

read the IN hunting regulations first, if your looking for a deer hunting rifle in this state it wouldn't hurt to call DNR and ask them about a specific setup. if I wanted to go huntin for deer id look at a 20ga so I could use it for squirrel and rabbit also. by the way, its not illegal to use a...

the only swap I might look at would be the 300 black out, anyone know where I can get a second centerfeed magazinefor when I swap stocks

I got my Stevens 200. got in a 22-250, decided that I needed onethe second I seen it. I figure it'll at least be good for coyote