Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Action Loose in Stock

Discussion in 'Handloading and Reloading' started by DanTheFarmer, Aug 24, 2011.

Thread Status:
Not open for further replies.
  1. DanTheFarmer

    DanTheFarmer Member

    Joined:
    Sep 24, 2010
    Messages:
    379
    Location:
    New Hampshire
    Good Afternoon,

    I'm trying to work up some loads for my 7mm-08 T/C Icon. The results haven't been meeting my expectations for accuracy. I cleaned my rifle this afternoon and as I put the bolt back in I noticed the action and barrel wiggling in the stock. Upon further inspection the Allen head type screws holding the action to the stock were extremely loose. I could turn them with my fingers.

    Here's a blinding flash of obvious type of question but I'm assuming that having the action that loose in the stock didn't do my accuracy any good. How much does a loose action affect accuracy?

    Should I just tighten the screws snug or is this a trip to the gunsmith needed for super secret inch-pounds of torque and mystical incantations?

    Should I repeat the loads I tried before I knew the action was loose or do the 8" groups (!) at 100 yards tell me to try a different load.

    Thanks.

    Dan
     
  2. cberge8

    cberge8 Member

    Joined:
    Jun 12, 2011
    Messages:
    158
    Location:
    Houma, la
    Get the loose stock issue fixed then retest your loads. I would assume the loose action could lend its hand to all kind of accuracy problems.

    To repair, back the screws out all the way, apply lock-tite to the threads (super glue can work in a pinch) and secure them down. I would wait overnight before shooting to ensure the lock-tite has cured. While waiting you could try some "mystical incantations", not a real gunsmith so I'm not in the loop when it comes to those.
     
  3. PecosRiverM

    PecosRiverM Member

    Joined:
    Jan 6, 2008
    Messages:
    97
    Location:
    D/FW Area, Texas
    I'd rather borrow some clear nail polish.
     
  4. MtnCreek

    MtnCreek Member

    Joined:
    Dec 8, 2010
    Messages:
    3,954
    Location:
    West GA
    Borrow?:)

    Contact TC and ask them what the proper method for resetting the action to stock is. They are great folks; at least they were about 10 yrs ago when they mailed me some free replacement bolts.
     
  5. kingmt

    kingmt Member

    Joined:
    Nov 17, 2009
    Messages:
    3,604
    You can find torque specs if you Google the bolt size, thread pitch, & surface it is binding but it might be easier to call the company & ask them.
     
  6. Huckelberry75

    Huckelberry75 Member

    Joined:
    Feb 28, 2011
    Messages:
    120
    Location:
    Oklahoma
    The removable lock tite is the cats pajamas on keeping things tight, while still allowing you to remove the bolts if you have to.
     
  7. popper

    popper Member

    Joined:
    Nov 10, 2010
    Messages:
    975
    Clean screws and holes with acetone (polish remover also works), use BLUE loc-tite, get torque specs from manufacturer. Keep a screw driver set in your shooting bag. I don't have or use an inch/# wrench, just snug up. Had the action screw fall out when I was shooting a new rifle once. Learned my lesson.
     
  8. gamestalker

    gamestalker member

    Joined:
    Sep 10, 2008
    Messages:
    9,832
    Location:
    SW Arizona
    I've used nail polish with many locktite applications and have never had a failure or difficult removal when needed. I wouldn't personally consider using super glue, just saying. But I would make sure the screws are properely tightened to spec. inch pounds.
    As for accuracy problems, yes, a loose stock is going to create all kinds of inconsistent groups.
     
  9. cfullgraf

    cfullgraf Member

    Joined:
    Oct 19, 2010
    Messages:
    7,135
    Location:
    East TN
    Nail polish remover is basically acetone. It might have some other stuff mixed in that makes it easier on the hide than straight acetone.
     
  10. jimmyraythomason

    jimmyraythomason Member

    Joined:
    Dec 19, 2006
    Messages:
    7,388
    Location:
    Alabama
    Alcohol works great as a degreaser before applying blue locktite. I torque all action screws (bolt actions)regardless of manufacturer to 65 pound inches. It is more critical that the screws are tightened equally and sequentually rather than to a specific torque spec.
     
    Last edited: Aug 25, 2011
  11. Skyshot

    Skyshot Member

    Joined:
    Jan 23, 2011
    Messages:
    936
    Location:
    Tn.
    I would retighten them and check and see if they come loose again. If they do, you might want to look at having the action bedded to keep it more snug.
     
  12. Seedtick

    Seedtick Member

    Joined:
    Mar 23, 2009
    Messages:
    1,049
    Location:
    Central Arkansas
    :scrutiny: Reckon it would still work ok if you filter it through your kidneys first? :scrutiny:


    I was taking a Blackhawk apart the other day to do some trigger work and all 5 of the frame screws were loose. I'm not talking barely snug or finger tight they were completely loose. :eek:

    Wonder when that happened??? And it was shooting purty durn good.


    Seedtick

    :)
     
Thread Status:
Not open for further replies.

Share This Page