Recent content by OnTarget1911

  1. O

    Duracoat Handguns

    EMP Yes I know I do this for a living but this is one I did recently. I use an airbrush and compressor from Harbor Freight. Yes Harbor Freight. And a table top paint booth. You could do the same with any air brush, Other people have had good luck with their spray delivery system. Jess
  2. O

    Some pics of recent work.

    Thanks all
  3. O

    CCW Pistol advice

    Get the heaviest .380 you can find..... That way when the bullets don't stop the BG at least when you hit them with it, they might stop...:what: I know, but I am just not a fan of the .380. Get the slimmest, lightest, and not cheapest largest caliber pistol you can shoot well. Even a .22 is...
  4. O

    Bluing

    Genn Rock bluing. They do all of mine and a lot of the custom gun makers out there. I cannot say enough good about Phil and Co. My other choice for top end custom guns would be Turnbull. Check gunbluing.com
  5. O

    Some pics of recent work.

    Just thought you might like to see a couple of my favorites.
  6. O

    A Good Alternative to DuraCoat?

    I always use Duracoat. I have also used Cerakote. People swear by both. I would just stick with the Duracoat. Paint is paint. Jess
  7. O

    1944 Remington Rand 1911A1

    If you want... If you want it looked over and don't mind paying for the shipping I will do it for free for you.. Jess
  8. O

    Been a while!! Custom S&W/Caspian BobC.A.T.

    Pics http://www.thehighroad.org/attachment.php?attachmentid=132226&d=1292383108 http://www.thehighroad.org/attachment.php?attachmentid=132227&d=1292383108 http://www.thehighroad.org/attachment.php?attachmentid=132228&d=1292383149
  9. O

    Best Bobtail Commander Under $1500

    Mine :) A S&W Scandium Commander bobbed and jobbed by me! ;) Jess
  10. O

    Been a while!! Custom S&W/Caspian BobC.A.T.

    Hi all, I have been laying low on this forum for some time. A LONG time as a matter of fact:cuss:. Just thought I would drop a few photos of a bobtail that I have completed Caspian Slide done in Duracoat Titanium SL eliminates external extractor for purists.:) S&W Scandium Commander frame Colt...
  11. O

    new to 1911's

    I don't know why I am answering your question again, just to echo what the others have said with a bit more information. The original 1911 was adopted by the military in about 1911 with the design dating back to 1909. It had a 5 inch barrel and slide, grip safety and short trigger. Then they...
  12. O

    Another BOB-C.A.T.

    I guess you guys are getting bored with the bobtails?
  13. O

    Another BOB-C.A.T.

    This one has the full BOB-C.A.T. package (carry and tactical:biglaugh:) Heinie straight 8s EGW innards Barrel crown Match bushing Frame to slide tightening 4 lb trigger Front strap stippling Snakeskin MSH Custom cut grips to match Full reliability tuning and range test I will be...
  14. O

    Range Test on 3 caliber 1911 Colt complete

    Just finished the range test with the 3 caliber Colt. No hits no runs no errors. It shot awesome. No breakin, no jams no nothing. This one is just one of those guns that just comes together right from the start and it has been in the works for a long time. Here are the targets shot from 15 yards...
  15. O

    Lint filled pics of super custom Colt in 38 S/9X23-9MM

    Perhaps I am just too picky. But there is a ton of lint on the gun, especially around the rear sight. I was talking with someone else today about this and between the new circumstances and new house, the shop in pieces and getting used to being single again, I guess I should just be happy that...
See more
Back
Top