Recent content by cajun 48

  1. C

    Favorite .45 (non-1911)

    favorite .45 S&W M&P full size!
  2. C

    Rifle die setup on Lee 4 hole turret.

    I'll be loading for a Marlin 270 win. F/L resizer will be in my single stage (for use when/if needed.) Think i have it figured out. Let me know if it'll work or if I need additional parts. sta #1 decap/neck size sta #2 powder thru die (with perfect powder measure attached) sta #3...
  3. C

    45ACP loaded with WST

    Specifically, 45ACP (full size M&P) bullet: dardas 200 lswc. would WST be a good powder? I know it's a bulky powder typical 5gr load net almost a full case (zero chance for double drop w/o a major mess). Is it dirty burning? help is always appreciated. aj b
  4. C

    Bullet choices for .270 winchester (130 grain)

    Choices, choices, choices! All in 130 gr. and using H4350 powder. Barnes TSX, Hornady Interbond, Nosler Ballistic Tip et al! Gonna be used for deer hunting (whitetail) and maybe pigs both under 200 yrds. Any ideas/suggestions? or am i worrying too much!:confused:
  5. C

    stupid reloading question of the week: auto pistol powder with large charge volume?

    try WST. it will not double charge in a .45acp. I use 200gr dardas swc and 5gr of WST and cut nice round holes. No problem feeding either.
  6. C

    45 ACP LSWC in Springfield XDM

    I shoot an M&P .45 and had the "no feed" problem. the fix was to seat the swc about 1/32nd below the edge. _/ \_ worked for me!
  7. C

    reloading for .270 winchester

    First, This will be the ONLY rifle round I will be loading. I have a Lee 4 hole classic turret press. And here comes the questions: The powder I plan to use is either H4831 or H4350 and the bullet weight between 130-150 gr. Will the pro auto disk measure be able to throw enough powder in 1...
  8. C

    Limp wristing

    You shooting, slide fails to cycle. . . Me shooting, slide cycles like it should. . . You limp wristed. . . If it fails to cycle for both of us, probably the gun and time to have it checked out! aj b
  9. C

    Semiwadcutters in M&P

    I have the f/s M&P .45. No problem shooting Dardas 200gr swc(bb) using 4.7 gr winchester WST. Mild recoil and 1" groups at 10 yards (old man, old eyes and a shake!) aj b
  10. C

    barrel length for deer hunting

    The gun is a 870 express 3" chamber. I have two barrels for it and was wondering which would be better for deer hunting. 1st is a 18" cyl choke (my h/d barrel) no vent bead sight 2nd is a 28" rem choke (modified) vent rib bead sight (not opposed to buying an imp cyl choke tube). Which would...
  11. C

    Winchester AutoComp (296?)

    When you go to the hogdon site and click on winchester products, place the cursor on autocomp and 296 shows up. Put the cursor on wst and wst shows up, thus the confusion. Also didn't know if the gun "had" to be comp'd to use the powder. aj b
  12. C

    Winchester AutoComp (296?)

    Is anyone using this powder for 45acp? How well does it meter? Is it clean burning? Is it useful for any other rounds (other than for semi-auto)? I'll be loading dardas 200gr lswc for my M&P. Thanks! aj b
  13. C

    Free reloading manual.

    rc, thanks for the freebie hook up. Free is always more gooder than payin'! aj b
  14. C

    cheapest place to buy 18" 870 12ga matte barrel?

    cheaper than dirt, in stock 106.99 plus 10 for shipping 5-7 days. 18.5" barrel, matte finish, 2 3/4" or 3", bead sight on plain barrel. aj b
  15. C

    Trouble W/ Lee Auto-Disc Powder Measure

    also try putting a 1/2" USS/Fender washer inside the hopper. For some reason it helps with metering (at least with mine). aj b
See more
Back
Top