Here is an inexperienced question, but here goes:
Is LC 308 brass considered comparable with any premium brass like Nosler or Hornady Match grade or is it comparable with commercial RP and WIN? I know the military brass is thicker and will hold less volume, but how does it rate in terms of...
I have a Rem 700 SPS Bull barrel that loves Sierra match HPBT 168 grain on paper. I decided to hunt with the rifle and have tried several different hunting bullets (Nosler Accubond, Nosler Ballistic, Nosler Silver Tip, Hornady SST)l but am unable to get the accuracy as I do the Sierra. I finally...
I purchased a lyman neck turning attachment for my trimmer and started turning cases. Before turning, the neck thickness varied from .010 to .012. In the process of evening out neck thickness, is there a source for the mimum thickness you should cut to for any caliber? Thanks in advance.
I am reloading 150grain FMJ using LC cases, win 748 powder and win primers. I crimp with a Hornady new dimensions die set. With that set up I can't get any better than a 3 inch group at 100 yards. I am not sure if maybe I am crimping too much and causing inconsistent loads. I want to load some...
I bought some Hoppe's Molybdenum Disulfide Dry lubricant. It claims it protects the bore and you can either spray on bullets or into the bore. Anyone have any experience with it? Not sure if it should be in the reloading, but if anyone would know, it is the reloaders.
This is all the info I could gather on my rifle.
HK 940
Semi - Automatic
Caliber: 30-06
Operating principle: recoil operated
Action: Delayed roller locked
Barrel length: 21.6 inches not including factory muzzle brake
Weight: 8.62 lbs
I have been shooting with the factory loaded...
Need Buehler High Scope Rings
I have a Buelher one piece base and low rings, and can't find high rings to fit a 50MM scope. I tried Leupold brand, but the front ring would not fit. Anyone know if any other brand will fit or where to get high rings? Thanks
I have a very old Marlin 22 rimfire and need some help identifyting it. It is clip fed. The only marking I can see on the barrel are The Marlin Firearms Company New Haven Conn USA 22 long rifle only smokeless greased. The Marlin customer service line was not much help. Thanks.
I purchased an Eagle Arms AR-15 and it fed the first 9 rounds of wolf ammo 62gr fmj with no problem, and then the next 10 jammed every round. I took it apart and thoroughly cleaned it including the gas tube and got the same results. I purchase brass cased commercial ammo and it ejected fine, but...
I have a Pacific Case Trimmer (has the Hornady name on it as well) and I need some case trimmer pilots. I wrote to Hornady and their response was ,"We're sorry, we no longer have parts for that old trimmer. Our current pilots will not work." Does anyone know of any pilots that will fit? Thanks.
I met someone who mentioned that they use an Alchohol patch down the bore after the copper cleaner to neutalize the copper cleaner (amonia). Then they clean with Hoppes and oil. Has anyone ever heard of this? Wondering if this couls cause any damage. My chemistry is a little rusty and wondered...
At the range today the bolt\extractor ripped the rim off a shell and left the casing lodged in the chamber. Is a broken case extractor the way to go? Any help in removing the case would be appreciated.
I had to send my rifle back to Ruger for some work and they replaced my trigger with the stock one. I have my old trigger that has been work. Anyone have instructions on how to install the trigger on ruger m77 with a tang safety?
Looking for instructions on how to adjust the Remington X Mark Pro trigger on my SPS. I have found the instructions on how to adjust older style (Sniper country), but not the X Mark trigger. Any help would be appreciated.
I had my rifle rebarreled by Ruger, and they replaced my adjusted trigger with a factory trigger due to liability issues. I have my original trigger and need instructions on how to install. I have done a few Timney triggers, but none like the Ruger. Any sources\instructions would be appreciated.
I have my son shooting managed recoil 30-06 in 125 grain from Remington. I would like to reload the same ammo. Does anyone have the recipe to duplicate the loads?
I purchased a Remington 700 SPS in 223 and the trigger is at least 5 pounds. Anyone know if there is any way to adjust the poundage lower? Or is this strictly a gunsmith item? Thanks.
I am reloading 30-06 rounds and only neck sizing them after they have been form fired. Since they are form fired and will only shoot them out of the same rifle, how often should I trim the cases? Neck sizing is supposed to help your cases last longer, but I read that you should not trim cases...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.