Search results for query: *

oops wrong post:

As a current NYS corrections officer, i as well as any LEO are indemnifyed from a private law suit while acting in accordance with department directives. What that means is the state will pay for the entire defence of the LEO, while you, joe citizen will need to come up with a very minimum of...

When i was a ny full service dealer 82-96, i had numerous troopers stop in to pass the time and i have to step in here with something you all should keep in mind. ANY large capacity ammo feeding device >10 rds can get you arrested. If you think it is on the trooper to identify a preban from...

choose your calibre wisely, the 43's were known to develope headspace issues in the 22 hornet chambering. The bolt heads were normaly shimed foward to close up headspace. A temporary fix on a shooter at best.

Yes, that is absolutly correct. As a CO, my badge exempts me from every aspect of the AWB. My conservative vote is always canceled out. Large city states such as NY have massive democrate voteing blocks who are mostly concerned with gov entitlements. Herman Cane "might" have been the best thing...

About ny dealers selling post or preban guns, a large dealer near by sells preban only to LE. Those guns that are pre ban or questionably will carry a blue price tag that means its sold only to LE or Corrections officers. They are exempt from the AWB untill they retire from active service...

Thanks for that clarification since the definition did not say colt ar15 "type" reciever where as that probably was the intent of the lawmakers who put it into law. Ignorance is bliss.....in this case? Unless "copies or duplicates of such weapons" is what they used as "type". As for stop...

I'd like to clear up a few things here as things have gone flying off in a few directions. The whole 20 gun issue is moot. Since as I originaly stated as a edit in the post, NY has "REVISED" the 265.02 (5) (i) to 3 or more guns. They simply changed the 20 to a 3 in the same extact sentence...

Hold on, He "claimed" there was no charges brought against him from the domestic dispute. He said this has happened before with the wife and after a "cooling off" period he has routeenly (2 or 3 other times) gone to the trooper barraks and retrieved his hand guns without any trouble at all...

Thanks for all the great info so quickly. Ill call the would be felon tonight and have him pull ip this thread. I was the dealer that sold him the woo way back then. The only thing missing from this story is the guy's wife called the cops on him cause he had one of his many arguments with her...

I have a guy I know that was just arrested by the NY state police for a pre ban Daewoo side folder. The Trooper didnt care one wit that he could have produced a 1980's bill of sale. He was booked, printed, cuffed and leg shakled befor the judge and alowed to post his own bail after he was taken...

The threaded shank of the 03 is far to small a OD to be rethreaded to large Ring mauser. If your 2100 has a barrel shank stop shoulder like the 98, it may be possible to cut a mauser shank foward the 03 shank and still end up with a minimum OD to shoulder up to the reciever face. But some of...

Pull the bolt out, take off the furniture, plug the barrel, and take it to a local body shop. Any body shop should be able to blast the unit down for you for that price you quoted. Then, its up to you to do a tear down to clean out the abrasive.

Alot of slides have a degree of warp to them, more or less. The frames are softer than the slide. I use a nylon hammer as a aid in removing drag points. Once you have filed the rails to where the slide goes on most of the way, dont be afraid of smacking the slide hard left, right and down once...

Frank Dehaas was the original Author of "the bolt action rifle" And I think he passed away while writting the second updated edition. I have the second edition and no one wrote a better shake down on a rifle action than Mr. DeHaas, God rest him. You might find one of those editions on the used...

25, I dont think you understood the issue. The 223 rim diameter is far smaller than the 7.35. You can not deep bore a new smaller bolt face on that bolt. Iv seen some smiths soft solder a new rim shoulder on the bolt face and deepen the ejector cut but I personaly dont like that type of "hump...

Im not a big Ruger fan but I just did some work on a brand new 308 gunsight Scout rifle and thought I would share what was done to make a good shooter. I fit an adjustable Hawkeye trigger to the gun from Brownells. This trigger's sear was cut very terribly on an angel and needed to be squared up...

A good way to tighten a loose ejector rod is to simply put it in a drill chuck that has clean unbuggared contact jaws, snug the chuck over the rod and then with 1 hand on the chuck and the other on the cylinder, snug the cylinder clockwise against the held chuck. I do this in a drill press but...

The off center forces on such a thin op piston rod would more than likely end up with either a fractured or bent rod. Too much push/pull on to thin a rod from off center resistence. Look at how well the Daewoo system is designed with center line forces between piston & recoil. Add to that the...

Heres just a few that got pictured along the way HVA action, Varmint wieght Lothar Walther barrel, Timney Trig, 25-06 Ithaca X15 with Thompson A3 30rd mags & adapter. Done back in the 80's Sako Lefty in 257 Roberts, Rem recoil lug, Ruger Alloy Trigger Guard Assm. Ruger 44 mag...