Search results for query: *

Found this site yesterday. It seems to search all my favorite sites, including auction sites Search For and Find Guns for Sale Online - GunWatcher.com Thought you might find it useful.

Contained in some donated components was a plastic bag primers, out of their trays, about 2-300, different sizes. I'm unable to identify them i.e. rifle vs. pistol reg vs. mag and would like to safely get rid of them. Can I throw them in the campfire? Soak them in oil? Flush them?

My cousin's declining health and finances forced liquidation of a life long collection of firearms over the last year or two. I facilitated the weapon disposition, very sucessfully on Gunbroker. I'm left with many, many thousands of rounds of hand loaded ammo, to dispose of in dozens of calibers...

My Dad's double action Llama target pistol has had a problem with dumping it's empties since new. It's clean, and has no friction when loading unfired rounds, but after firing the brass can be a real BEAR to eject. To the point of having to tap the ejection rod with something in the worse cases...

I have a new Rossi M92 Lever Action Carbine in .45 Colt I'm breaking in. I want to develop some accurate loads with the Missouri Bullet Cowboy #1 and Cowboy #4 (Lead 200+250 gr RNFP #12 Brinell) I Have AA#2, AA#5, IMR4227, Universal Clays, Blue Dot, H110 Has anyone had experience in this...

I'm loading for an upcoming Prairie Dog Adventure in June. Three different rifles, three different maximum COAL's with the same varmint nightmare 55gr SP bullets. Teh COAL ranges from 2.235" to the lands on my shortest chamber CZ-527 to 2.307" on my longest chamber Savage 12FV How much...

I'm stockpiling for this summer's prairie dog adventure. Looking for a thrifty source for once fired, non crimped .223, preferably not mixed head stamp, decent once fired brass. I can process, but prefer not to remove primer crimps. Anyone have a suggestion for a reliable source for 2-3k cases?

I'm spending the colder months stockpiling a bunch of .223, hopefully for a first ever PD hunt this summer. I'm looking at Midsouth and their varmint nightmare & varmint extreme bullets... Do I want SP or HP? My rifles are all bolt 1:9 twist and I have a bunch of WC844 Pulldown Powder...

Well, I got to take my new Winchester 1885 Hi-Wall replica to the range yesterday. It's the 22" Hunter Model. It was 11°F Brrrrrr! I sent my first 12 Missouri Bullet 300gr RNFP 45-70 rounds downrange pushed by 30gr of H4198 and they shot great. One big ragged hole as I sighted in at the 25y...

When using the largest single hole drops (1.57 volume) I can't get the actuator to move the disk far enough. It leaves a shelf on the base plate, which is causing inconsistant drops. The case is fully seating in the charging die, it just isn't moving the actuator arm far enough for the larges...

I'm trying to squeeze thaat last little bit out of my .223 Savage. Do you have a favorite budget minded neck turning tool?

Well, I've managed to develop a load for my Savage 12FV in .223 Remington 40 gr Sierra BlitzKing over 22 Grains of H335 is putting in one ragged hole :) I need to put together a couple thousand rounds for a our first Prairie Dog Hunt next month. I'm wondering whether I should buy some...

I'm loading my first batch of these into .357 cases. The are soft (Brinell 10) double ended wad cutters from Missouri Bullet Co. I'm seating deep to the second crimp groove. They're just for paper punching, 15-25y. I have a lot of Alliant Bullseye powder too. Any suggestions for light...

Well, thanks to the help here, I've successfully loaded about three thousand 9mm pistol cartridges over the last few months. My next two calibers are .357 Mag and .223 Remington. First the Pistol, anything special I'll need for .357? I don't trim the 9mm now. Now about the rifle, I'm...

Would .32 Auto, .32 Long and the new .327 Magnum each require a different die set?

I've carefully finished my first batch of 9mm for my HP 995TS Carbine. The case width has a barely noticeable 4 thousandths indentation in the overall taper from the mouth to the rim. The indentation is just after the area where the bullet seats. The OAL is fine. I set the FCD to only crimp...

I'm having issues with primer seating on my Lee Classic 4 Hole Turret. I'm loading 9mm with small pistol primers. After the primer is properly fed, (thanks for the tip on the washer under the safety prime) the metal arm holding the primer that tips in to insert the primer in the casing is just...

I'm having issues with my new Lee Safety Prime on my Lee Classic 4 Hole Turret. I'm loading 9mm with small pistol primers. When I press on the primer feed, it only only wants to load 1 out 3 in the pocket. The other two times it either fails to feed a primer, or piddles one on the floor. What am...