Search results for query: *

What is the current waiting time to process your Form 4 for a trust? Mine was sent in November.:confused:

I intend to purchase a suppressor and want to form a trust to do so, but all I have seen on the net cost over $100 to form a simple trust. There must be a boiler plate document out there that will work. After spending the $200 for the stamp, I am just trying to keep my costs down. Thanks

The other day I was at the range and had a fellow tell me that his .40 was not feeding and ejecting very well. I picked up this brass off of the ground and saw the attached picture. Just goes to show you that Murphy is never far away. Fair warning kids, do not try this at home:evil:

My daughter has been visiting and we have had some range time but I want her to practice gun handling when she get home. I made some dummy rounds for her to practice with here but want to send some home with her so I have made up some dummy rounds (de-primed brass without bullets and some...

I just bought a thousand Precision Delta 148gr. Hollow base lead wad cutters. I am loading with Lee dies. I can't get the bullet to seat past the last lube groove without putting a big crimp on the case(crimp from the seating die). If I don't fully stroke the press I can get just to the lube...

I thought that I had read that the bill for national reciprocity for a CCL had moved forward but haven't read anything since that time. What is the current status of the bill?

I am looking for a light load with 185 gr lead simi wad cutters. Looking for accuracy and light recoil. I usually load with Unique.

This is actually the second report. The first was on a friend's new gun and this one is on the one I just bought. The fit on these little pistols is very good. I paid under $500 drive-out. The first one had problems going into battery and a tap on the slide would fix it. My gun would...

I received my ATI FX45 Titan last week. The First trip to the range did not go well at all. The first 20 rounds of round nose 200 gr. reloads fired without a FTF. When I ran out of those I switched to HSM 230gr. HP(Copper coated lead). These would not load at all. The slide would not go into...

Just back from the range with a new ATI Titan (blue). Put about 100 rounds of 230 gr. JRP through it with out a problem. Shot reasonable groups for a short barreled pistol. After the shoot, took it apart and found it to be really well made for the money. There is no barrel bushing and the...

A friend just bought an American Tactical .45 Titan. I had never heard of it. It's made in Manila. Is this another brand name from Rock Island? Also ran across a 1911 called Metro which is also made in the Phillipine Islands. Three 1911 manufactures in such a small country seems a bit odd...

I just got some Winchester NT and some Federal brass that has small primer pockets. My references do not have any data for loading using small pistol primers with their loads. I have been loading with No 300 Large Pistol Primers by CCI. Can I use the same loads with No. 550 Small Pistol...

Our club uses 1/2" OSB plywood as backing for our targets on both the rifle and pistol ranges(Supports are made of 2x4's and don't get hit that often). The 10 yard pistol backing is torn up within a week of being put on. We normally change them out once a month. Does anyone know of a material...

I have noticed that the outside of my spent brass (.40 S&W & .45 ACP) have black scorching 3/4 of the way down from the mouth. I am shooting light loads in both guns. I noticed that the factory loads I have picked up on the range don't have any or at least less scorching than my loads. Is...

I am loading 40 S&w with 135fp bullets and Bullseye powder. Lee recommends starting load of 7.0grains and a max load of 7.6 . Lymans recommends starting with 5.5 grains with a max of 6.3. Bullseye dosen't have a 135gr load but for the 155gr they recommend 6.0 grains That seems like a...