Search results for query: *

  1. T

    What have you done in the reloading room today

    He got me worried there because I had just bought a 45-70 mold thinking it was .458 which it is.
  2. T

    What have you done in the reloading room today

    Stupid question but doesn't 45-70 take a .458" bullet diameter? I have a 45-285 FP-FB which I used for the first time about a week ago. I will be using it for 45 Colt and 454 Casull. I also have a 45-70- 350 FPD/BB mold that I just received. I have yet to try it.
  3. T

    What have you done in the reloading room today

    You were supposed to run out and go buy a 408 Cheytac.
  4. T

    What have you done in the reloading room today

    I finished chamfering and deburring my 80 338 Lapua cases, and then primed them all. I loaded another ladder of 223 for my HK SL8 using Hornady 55gr FMJ’s, IMR 8208XBR, and Federal GM205M primers in Lake City Brass.
  5. T

    What have you done in the reloading room today

    I have the RCBS media separator. I fill the bottom with water spin it about 10 times and there’s not a pin left in any size case. What I like about the RCBS media separator is that it has a cover so water doesn’t splash everywhere.
  6. T

    What have you done in the reloading room today

    3/4 of the way through trimming 80 pieces of 338 Lapua brass on the Sinclair/L.E. Wilson trimmer.
  7. T

    What have you done in the reloading room today

    Made myself a new cover gasket for the Thumlers Tumbler. I used my chamfering and deburring tool to sharpen up an old 338 Lapua case to cut out the holes. I don’t know why I waited so long to make a new one. It cost me a whole $1.50 in material.
  8. T

    Reading about Ruger Revolvers

    I’m surprised since his review was mostly positive. I really like mine. I picked it up used for a good deal and I would buy it again. My only other revolver in 357 Magnum is a 1977 Royal Blue Colt Python. Even though these 2 revolvers are not exactly in the same zip code when it comes to price I...
  9. T

    I realized today… I just can’t shoot GP’s very well.

    I have the same grip on my Match Champion. It’s probably the best grip from any of my revolvers
  10. T

    What have you done in the reloading room today

    Loaded 18 rounds of 45–70 to fill this little case. Loaded 460S&W with my last 30 200gr Hornady FTX over 49.2gr of H110. I thought I had another box of the 200 grain FTX, but the box was full of 140 EDM‘s
  11. T

    What have you done in the reloading room today

    Loaded another ladder for the HK SL8. This time using Speer 52gr Varmint Hollowpoint bullets, Ramshot Tac, CCI 400 primers in Federal brass. I've been having a hell of a time getting this rifle to shoot small groups. Other people claim it's sub MOA or close to it. I have to work on Saturday so...
  12. T

    Primer anvils??

    Yup, it's electric. I was checking on inventory searching for some Vihtavuoriu N110 and some Hodgdons H110 that I knew I had stashed somewhere. They were stored somewhere else.
  13. T

    Primer anvils??

    If I can't buy any primers and I don't have stock it means that my preparations failed. I try to be prepared. There are 5K each of BR-2 and BR-4 on top of the Zero Brand bullets.
  14. T

    Primer anvils??

    I think I would start collecting cans and bottles and bring them to the redemption center to pay for my primers before I would spend the effort on reloading them. Even scrap metal collecting would be a more worthwhile endeavor.
  15. T

    Anyone use a radar based chrono near the ground?

    The target is typically 3 to 4 feet off the ground. I usually have it on 8 inch offset. I’ve never had an issue with it, picking up the bullet..
  16. T

    Anyone use a radar based chrono near the ground?

    When shooting from the prone position, I put the LabRadar on a tripod straddling over the barrel
  17. T

    What have you done in the reloading room today

    Finished printing the Lee Lead Hardness Tester stand. Whoever designed it wasn't a genius. The gear isn't splined on to the rod that turns it so it just freewheels. It's still usefull the way it is. Loaded a ladder of .223 to test in my HK SL8 IMR 4166 with Federal brass, CCI 400 and 77gr SMK's...
  18. T

    What have you done in the reloading room today

    Deprimed and sized 80 pieces of Lapua 338LM brass. Off they go for a swim in SS Pins.
  19. T

    What have you done in the reloading room today

    In the process of 3D printing a microscope stand for my Lee Lead Hardness Tester. I also woke up early and loaded 50 44 Magnum with 19.9gr of Vihtavuori N110 over a 240gr JSP.
  20. T

    Need starting load suggestions 454 Casull with powder coated lead 285gr FN-FB bullets.

    Thanks, I couldn't find any load data for Accurate #7 but I plugged your data into GRT and you seem to be right on the money.
Back
Top