Search results for query: *

  • Users: Riss
  • Order by date
  1. R

    Ruger Mk2 troubles

    Checked all the above. All appears to in tip top shape, all parts are installed and in the correct configuration. Will attempt taking it all apart again and putting all the old parts back in and seeing if it wants to work.
  2. R

    Ruger Mk2 troubles

    If you mean the trigger spring that goes in the top of the trigger and holds up the disconnector, its in there. The overtravel screw was taken out. The trigger appears to be going to full stroke but the disconnector is not moving enough to pull the sear away from the hammer. The sear is not even...
  3. R

    Ruger Mk2 troubles

    Installed and then uninstalled a Volquartsen hammer and sear now I cannot get enough travel out of the trigger to move the sear to drop the hammer. No parts left over and have installed and reinstalled the old and new parts several times. I still cannot get it to work. The trigger is barely...
  4. R

    stoger o/u problems

    Brownells and I am sure others also, sells cupped tip punches to properly center on rounded head pins.
  5. R

    S&W wear signs : flame cutting to top strap

    I am in light negotiations to buy it. I am low balling on the price because I first saw the cutting on the top strap. Not knowing where else to readily look for problems I will not make a firm price. I have other revolvers, none in 44 mag, but they are not marked at all like that after 10's of...
  6. R

    S&W wear signs : flame cutting to top strap

    It's a Lew Horton 3" adj sights, compact rosewood grips, etc.
  7. R

    S&W wear signs : flame cutting to top strap

    It was flame cutting. I did not try to scratch it off, but I am sure it is not lead.
  8. R

    S&W wear signs : flame cutting to top strap

    Well it is a custom run S&W model 28 and I do want one in the stable. The finish is not bad at all and the gun overall is about 90 %. But it was apparently fed a steady diet of full power 44 magnum shells.
  9. R

    stoger o/u problems

    I have seen others with the same problems. I assume that a good cleaning and polishing of the internal fire controls should fix the problem.
  10. R

    S&W wear signs : flame cutting to top strap

    Where else should I look for signs of wear for a 44 Mag S&W other than the top strap ? Barrel cylinder gap is the next obvious check. But what else can I check to see how bad the gun is worn ? To clarify, the top strap has MAJOR flame cutting. Looks like someone ran a hacksaw over it.
  11. R

    Shortened Glock slide stop?

    Never saw a shorter one. Your best best might be to alter your grip.
  12. R

    Glock 22 extractor/ LCI install.

    Not sure who ryg.com is but replacing the extractor should be the same as on the first 3 gens of Glocks. With the slide off turn it over and push the little black spacer that you can see next to the striker, forward. This will release the tension on the back plate and you can slide it down and...
  13. R

    My Ruger LCP Crumbled!

    Do you practice with a lot of dryfiring ?
  14. R

    Greenish Colored Parkerizing

    I usually start with a dead cold bath and very slowly bring the temp up. When I see it starting to turn color or bubble I try to level off the heat and keep it there, not sure what temp that is, but keep it constant until the little bubbles stop. When the parts are good and black and no more...
  15. R

    Greenish Colored Parkerizing

    I have had luck using varied temperatures to get different colors. Hot usually gets a green or gray/green and if I start out with a cold bath and cold metal and bring the temp up slowly I can usually get deep black.
  16. R

    Greenish Colored Parkerizing

    I think it looks good. Care to share your method ?
  17. R

    Slapping the trigger....how do I stop it??

    Unless you are good enough of a shooter to slap the trigger and get good results your best bet it to use the trigger reset technique. Watch the front sight, drive the gun where you want it to go and hold on. Keep up your cadence when shooting multiple target arrays. That and 5 million other...
  18. R

    C-More slide ride, what size dot ?

    I am looking at setting up my Glock 22 for USPSA open class. What size dot would you recommend for a C-More Slide Ride ? what size dot are you using ? I was figuring 8 moa, I think that the 12 moa would be a little too big. But then again my eyes are not the greatest.
  19. R

    First time garage sale success. Lets hear your garage sale stories.

    Got an almost new in box 1966 vintage S&W Model 28 Highway Patrolman last year for $260. Did not even look like it had a box of shells through it.
  20. R

    CZ75 Problem

    This may be a question for one of the guys on the CZ forum. There are many guys there, including Angus Hobdell that really know their stuff on the CZ.
Back
Top