Search results for query: *

  1. C

    Inline Fabrication roller handle for LNL

    I took a piece of 5/8s round bar and made my own short ergonomic roller handle. Works great, I resize everything with it, 223, 204, 22-250, 45acp, 380acp. Works great.
  2. C

    Bad feeling

    If your not 100 percent sure, I would pull each and every one. Or burry them in the yard and start over.
  3. C

    Somebody convince me to like black rifles

    Do this with your mini. Group at 440 yrds, with my rock river predator pursuit.
  4. C

    Truck Gun dilemma

    I keep one of my ARs under the seat. Plum crazy lower, with a carbon fiber hand guard. Don't mind leaving it in the truck year round. Only part that can really rust is the barrel.
  5. C

    ar 15 build

    I've bought upper receivers from surplusammo.com. I've been very happy with them, most all other parts I've used came from joeboboutfitters or midwayusa. Be carefully, it's an addiction. I build my first one a year ago and look what I've done.
  6. C

    How long can I run a tumbler

    I always tumble my brass at least 12 hours.
  7. C

    Brass addiction

    I too am a brassaholic. I find When I'm shooting ARs that I'm more concerned about where my brass is going than my bullets are going. Doesn't happen often but when I do shoot at a range I spend more time searching for brass than shooting. It's pathetic
  8. C

    Changed to Hornady LnL AP from 550 Dillon.

    You'll get used to it. I have found when loading 223 and extruded powder, you have to delay at the top to make sure the powder has enough time to flow. Its then when I am grabbing my next bullet first then a case. Because it is easier to set the case in the shell holder using odd fingers than it...
  9. C

    Show us a picture of your reloading bench

    Got hocked on the big red H this winter and bought two new presses powder dispenser and a line of new hornady dies! Mec 9000g not pictured.
  10. C

    Hornady LNL Issues ?

    I have only had my lnl ap for a couple months but have put a couple thousands rounds of 223 and at least 500 204s. I guess I have no major complaints, my shell plate wouldn't stay tight, tried a star washer, still got lose. Finally used some temporary lock tight and that did the trick. As for...
  11. C

    Calibrated my Hornady Classic to my hornady AP

    Alright here it is. I made 4 small shims out of some aluminum I had measuring .15 inches. I stuck them under my lock n load socket and I used a bullet seating die to seat a bullet in each press without changing the die and got them within .002 of each other. One COAL ended up at 2.25 and the...
  12. C

    Running a Hornady LNL AP out of primers

    No, i don't remember seeing it in the video either. I think they added it to the kit after the fact. I also marked my rode so I have a reference when I'm nearing 100.
  13. C

    Case Bulging To One Side at Bullet?

    BDS+2
  14. C

    Pros or Cons on Hornady or Dillon presses

    I love my lock n load ap. loved it so much I bought the lock n load classic press. I then calibrated the two together by making some shimes and now I can drop a due in either press using the lock n load bushing and no more die setting. I'm sure the Dillion is great, but if cost is a...
  15. C

    Tell me the CONS of the Hornady LNL AP

    I love my hornady, I've only had it a couple weeks but have loaded around 1000 rds with it. I did adjust the paws a hair, and ran a dremel on the plate the primer system slides on. Other than that its workin great. I know plenty of people with dillion presses that have all the same...
  16. C

    Lock n load ap mods

    Just got my Lock N Load press last week and already I've had to add to it. first time uploading pictures, hope it works. first thing I did was made a roller handle. second thing I did was add a mechanical counter, clicks on the downstroke. third, JB welded a small LED...
Back
Top