Search results for query: *

sounds like the store gave him the wrong ammo.

.357 sig is a necked down 40 but it wont headspace properly and the bullet will rattle down the bore if it would shoot,let alone being a safety hazard.the only way that is correct ammo is if the cases were origionally marked sig,but not necked down and then loaded as 40,which may be the case,but...

the best load manual is just a starting point.different lots as well as a different gun means that you work up.all you need from a manual is a starting point,to work up from.10% under the manual max is usually safe.i like to look thru several manuals for a load with a given powder and bullet...

even when neck sizing a lube should be used.for heavy sizing down i use a lube pad and rcbs lube.for fl sizing i use a spray on lube.for neck only i use powdered moly.yep,the expander works best if polished.

i go a bit farther than resizing on a single stage.i deprime only so i can feel the pressure required.i also like to use a old style tl jr without progressive linkage and a 300 mag cmr die.

i have even had the experience of a starting load having excess pressure,from a published load manual.if the manual does not show pressure a bit of extra caution may be in order.remember,the same exact components in a different chamber can require a starting load as well.

havent used either but go to the hornady website and e-mail a question.

yes powder will get old but the owner will deteriorate faster than properly stored powder.i have shot 50 year old powder that had shown no sign of deteriation.lot to lot variation can be more than what was shown on the load data of 2400 in the earlier post.some of alliants powders are faster...

i normally use a hand priming setup.it doesnt take any longer because i use loading blocks and run all cases thru each operation.used the priming setup off my t-mag on the spartan and thought it needed some re-engineering.the plunger that holds the primer in the arm is a bit too low.some brands...

i suggest a single stage press to start with,and a cast iron body adjustable measure,a decent scale,a universal type case trimmer ,and a pair of calipers.ad goodies as you feel the need.this stuff wil never be outgrown unless a large volume is wanted

many calipers will get a different reading at the base of the jaws than at the tip of the jaws.good calipers can be adjusted.

rcbs rc2 with a piggyback,lyman tmag with extra turret(hate to reset dies)lyman spartan single stage(cause i found one for a buddy and hated to give it up and got one for me)5 lyman truline jr turret presses (cause just one more makes perfect sense to me),some of these are dedicated to one cast...

been casting for and shootin a marlin since 79 and a sbh since 82.plain ww and a good lube are fine with full house loads.a bit of tin (2% works) makes a more purty,sharply defined bullet.ditto on dropping into a bucket of cold water.makes them hard enough you cant hardly scratch them with a...

if you reload a vareity of rounds ,then you will want one measure with each!! it saves setup time.i have a few measures setup for specific charges.

i have used the rcbs for years with total satisfaction.i have bought a few lyman 55's to keep preset for a given load and like them as well.a friend bought a lee perfect and all i can say is it is a perfect piece of junk!! buy a measure made of metal,not plastic unless it is a set of scoops and...

one of the bad things about the 400 is corbon ammo costs $26 for a box of 20 at the local shop.only bought 1 box to baseline my loads .wanted to check velocity and headspace of factory ammo.havent seen it listed in the usual mail order sources.bottom line,if you are gonna have fun with it and...

what i like about the 1911 is you can customize it just about any way you want it.mine started as an essex frame,new for $47 in the 70's.my gunny sarge brother in law built it for me and didnt want a dime.civilian slide and barrel plus new innards.pretty much mil-spec a1 configuration.always...

first deer in the 70's with a marlin1894 in 44 mag,after that 243,25/06,6.5/06,killed over 50 with the 25,only one that needed a 2nd shot,i missed,offhand at 275 yds on the 1st shot.lost only 1 in 1987...ruger sbh/180 jhp/1900 fps/30 yds/lookin at me/dropped its nose when the trigger broke/hit...

the attractive part of a 400 corbon conversion is its cost and simplicity.i have a 1911a1 ,only the barrel and recoil spring need be changed.my barrel has a link and pin to make changes easier.it also has its own bushing,however with my barrel the 45 bushing fits close to the same.true that a 45...

the pix show a 4 didgit number,not clear but there.just occured to me,may be the last 4 numbers.they are on the fore end arent they?