Search results for query: *

In like Flynn

excellent, will check it out!

I just purchased the 220 super match. This firearm is fantastic. I am a little dissapointed that they did not adopt a stainless frame rather than an alloy one. The extra mass in my my x-5 definately helps with recoil management and I wish it were available in the 220 super match. I've...

springfield makes a 9mm 1911 loaded that frequently makes its way into my range bag

Went to ETSU for undergrad and grad school. I absolutely loved it there. May wind up moving back sometime.

I have a CCW here in Alabama. In fact several of my collegues were "character references" on my application. Unfortunately, I am unable to carry at work due to the rules at these facilities. At all other times I never leave the house without the PF-9. I would say many people I work with...

I am using the coated lead bullets from precision. They are the 115 grain Flat points

I can't seem to find any load data in the Lee reloading manual on: 9mmx19mm lead 115grain bullet Unique powder There is data however for 125 grain lead and Unique powder. They suggest starting at 5.3 grains and 1.15 OAL I've heard that using load data for a heavier bullet would be...

I upped the charge to about 4.8 Reliably cycles my springfield 1911 fullsize. It has very moderate recoil and seems to be way more accurate than the WWB that I usually shoot

Whoops, I forgot the most important information of all. Yes above load data for .45ACP

I'm trying to get a load for .45ACP that would be good mainly for just target shooting. When I looked in the LEE reloading manual these are the specs I got for a .45ACP 200grain lead round nose bullet. I am thinking of using: Unique powder 4.2 grains .45ACP Lead 200grain round nose from...

Sent you guys a PM but never heard back I'm looking to buy a BHP from CD but heard nasty rumors that it may be in the process of being discontinued? Is this true? I kind of doubt it as I heard it at a gunshop. Nevertheless i'm saddened to see that more manufacturers haven't picked up this...

Great vendor!!! A+. I've bought 3 kits from him and his refinishing is top notch.

I guess I don't exactly know what that sentence means :confused: It seems everyone here is trying to read more into my statement than what is actually there. My only point is that this process to reinstate one's rights after being previously adjudicated will likely be a joke especially where...

Sorry if I didn't spell out the process to a "T" Are you picking apart my verbage to make it appear that I don't understand the process when infact I do? Are you are trying to minimize my point by saying that it is rare that someone is involuntarily committed and if they are that perhaps they...

You can cut the sarcasm. I've not even read the GOA's response to this bill. My post came from reading the bill and responding. You made some assumptions about my post and were dead WRONG :banghead: There will obviously be a hearing and testimony in the adjudication process. MY POINT is...

Riggghhhtt. Getting off that list is probably going to be as easy as getting a CHL in San Francisco or Washington D.C. While I'm sure that the GOA's message may be a little alarmist this is not benign legislation. Due Process just means that someone can take their merry time to say "no"...

As the title says is the Monarch 9mm brass (prvi partizan) in 9mm reloadable? You can buy it from Acadamy in green boxes

The sand cloth method worked perfectly. I used the plastic butt end of a screwdriver though instead of a hammer. I layed down a very small patch of sand cloth over the concerned area and gently rapped the plastic end of the screwdriver into the paper. 5-10 minutes later I can't tell where the...

Just a quick question before I attempt some touch up work on one of my pistols. It is a 1911 in stainless with "dark grey" rounds that I'm guessing would be called a "matte" finish. It has a texture to it that feels a little more smooth than parkerizing. It looks identical in color and...