I wouldn't bump the old one so I thought it would be OK to start another.
Time to bump this back up.
All these targets were shot offhand at 15 yards using a 200g. LSWC over 4.3 grains of Bullseye.
First up is one I shot today. Les Baer Premier II:
Next, Les Baer Thunder...
[B] I have a Smith & Wesson 1006 that has about 600 rounds through it. After running 500 trouble free rounds through it I am getting failure to eject issues ever magazine. My handloads are on the hot side (180g. bullet 1300 fps) which is a max load. Even with weaker factory UMC loads the results...
I am setting up a brand new RCBS Summit press with Redding competition dies for 308 using a .336 bushing.
After getting the neck sizer setup I am getting 8 thousands of runnout on the case neck on my once fired cases. Before they are sized at most they have 1.5 thousands so it is the neck...
About a week ago I picked up a new SCAR 17. What an amazing rifle. Only complaint is the 16" barrel. Too short for 308 in my book but if they ever make an 18" it will be on my Christmas list.
After playing with irons for a while I decided to mount up a Vortex Viper 2.5x10 to test some...
Hello all,
I have a head scratcher here you might be able to help me sort out. First of all I know light .223 bullets in a 1/7 twist can cause jacket separation. After doing some research and in need of something to feed my AR I ordered Hornday 50g. V-max bullets to try.
The rifle is a...
Hello All,
I am currently (until about an hour ago) using a Lee Auto Prime Hand Priming Tool. It has primed thousands of cases and worked great. I had it upside down with a fresh tray of primers when the elevator pin dropped out. I am not talking about the seating pin but the first one that...
--------------------------------------------------------------------------------
The gun was purchased in December of 2009 when it was fairly new. Since I am in California it came with a neutered full size magazine without the load button which makes it a bitch to load. Since then I got a...
On Saturday I pick up a Performance Center 625 with a 4" barrel. This is my only wheel gun simply because the semi-auto's feel better in my hand. A good buddy of mine is a revolver fanatic and after shooting lots of his different model wheel guns I decided to order the 625. The main reason I got...
I am looking for a good quality open carry belt holster for IDPA, USPSA holster made of plastic. Blade Tech is among my favorite make for my Glocks but I can't find anything for my 4" 625 S&W. Just not into the leather or nylon holsters and want something more rugged. Safriland makes a thiner...
Hello all,
I just got a new KKM barrel for my G19 and loaded up some Missouri 147g. LSWC's http://www.missouribullet.com/detail...ry=8&keywords= and need a bit of help. The load I am using is
147g. LSWC
3.1g. & 3.3g of Universal Clays
1.135 OAL
Tula Primer
I ran 10 of the 3.1g...
If I could not modify the Glock I probably would not own one. The trigger is just too heavy, grip too slick and sights awful. As a reloader the cost of reloading doubles when the only bullets you can safely shoot are FMJ or plated. Even the moly coated by Precision are about as much as Montana...
Ok guys and gals, here is the challenge. I am looking to replace the stock on my VEPR 7.62x39 to a more conventional AK. Here is what the rifle looks like now.
This is what I want the rifle to look like:
Keep in mind I don't want to cut anything off the rifle. Some adaptors are made...
Hello all,
I have checked my Lyman, Speer and Winchester's website but still can't find info on my bullet and powder. All they give data for is TMJ SWC. I have 185g. LSWC from Mastercast, Bullseye and 231 powders to try. Can any of you great folks give me a good starting load for a 5" 1911...
I have been looking at the Winchester load data site looking for a hot load to use for my Montana Gold 185g. HP's. According to Winchester 8.2 grains of Longshot powder will push a 185g. bullet to 1044 fps. I use Longshot for my 10mm and it meters very well and works great. I have never heard of...
I am writing my reloading list for 9mm and would like some imput on bullets. I am going through Montana Gold Bullet Co. for the order. I have shot many thousands of them through my 1911's and 10mm Glock with fantastic results. 9mm handloading is new to me but I intend to load them on the warm...
I got my New G19 out to the range on Friday and loaded up a full magazine. Round one cycled and fired like normal. I squeezed off another round and felt the slide shift forward a bit and heard the striker fall but no boom. I ejected the offending round and noticed this off center light strike on...
The question refers to major power factor loads only. The reason why I ask is because I am looking for a gun to compete in limited 10 USPSA. The gun I am lookng at is a USP Expert which I can get in .45acp and .40 S&W. Thanks all, Sammy
Hello all,
I am new to the 10mm round and have a few questions. The gun I am using is a Glock 20SF with a KKM barrel. The Glock stock is plenty accurate and the only reason I got the barrel is to save the brass. This weekend I shot 100 factory UMC part# LC L10MMG 180g FMJ flat nose. I am...
I am attending a tactical rifle match next weekend and have Golden Tiger and Wolf FMJ in 7.62x39. Both are made with a steel jacket and lead core. Is this going to be a problem with metal targets that are made for rifle rounds? I have searched companies making rifle steel popers and targets and...
I am strongly leaning toward the Burris XTS-135 but I am torn on just getting the Aimpoint. I have heard very little on the Burris but they have been on back order for the last 6 months. Optics planet is getting them in stock next week.
The Aimpoint is option 2 and is about twice the money...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.