Hello my name is Kyle and I just got a steal of a deal on a Puma 92 Scout Rifle. This is the Puma that comes with the removable rear comb and long eye relief scope installed. Well I have no use for the scope or comb because I want to shoot this gun with the sights. I am wondering since I got...
Hello I have a Remington 700 SPS Varmit .308 and I am having a bit of difficulty with doing up some new reloads. I am using both the RCBS Pre. MIC and the Stoney point OAL lenght gauge. When I use these tools the OAL is a lot on the Stoney point gauge the bullet when it meets the lands I back...
Well I today I posted a topic that was asking about a Glock 36 or a Colt Defender. Well just a little bit ago I shot a XD45 Service 4inch and loved it, so I need you to tell me why I should not get this handgun because BUDS has them for 449 with shipping right now. Im thinking about keeping my...
I have narrowed my personal protection weapon down to the glock 36 or Colt Defender .45. I was just hoping you all could help me with the descision between the two.
I need help find a really nice single stage press. I have a Dillon Square deal B that is way overkill for the amount that I shoot so I am wanting to downgrade to a single stage "the dillon is for sale if anyone is interested". I have a lee single stage that came with my aniv. kit but I dont...
Hey anyone out there have a 22 conversion for there tuarus 1911? I am wanting to buy a 22 conversion for my PT-1911 but I am really not sure which one to buy because there are so many.
I am just curious about Oregon Trail Lazer Cast Bullets. I have a case of 500 in the .45LC bullet and I am about to load them up with my Dillon SDB, do I have to do anything different with these bullets when loading, or do I just start loading? I think I read somewhere that you need lube with...
So COL or OAL is what i want to make my end product be right or what the OAL of my bullet? And this is different than MOAL or Max OAL, right. Ok and what about a crimp for .44 in my marlin 1894 rifle should I give it some crimp? How much whould I put on it, I will be using the Lee factory...
Hey guys I have a question for loading .44mag loads for my lever rifle and for loading 45LC for my vaquero. How do I get the OAL do I just measure a factory load and use it?
Hey guys I was wondering about a nice load for my Ruger Vaquero 4,3/4 inch barrel. I am getting the Oregon Cast 250 RNFP bullets I have CCI LPP and I am trying to pick between Reddot and Titegroup. Any suggestions? I am also kinda wanting this powder to be able to work with my .44mag lead loads...
Hey guys I just got my new Marlin 1894 .44 mag rifle I bought some componets and I am wondering where to start.
This is what I have
XTP 240 gr
Jacketed FP 240gr
Lead FP 240 gr
I have H110 poweder and CCI LPP
I am wondering if there is a good starting load I could use for all of these...
Ok this is what I did this morning,
I took one of my brand new rem. brass and ran it through the full length sizer.
I then went to chamber it and guess what it worked great!!
Now what it the process so that I know it for sure with both used and brand new brass. Does it go like this...
Hey guys whats up? Well today I took my new Savagge rig to the range with 20 Rem. UMC and 20 of my reloads. I shot all of the umc's and got the scope on paper at 100 yards so then I decided to switch to my reloads. I went to chamber the round and it did not feel right at all. When I push the...
Well my omega is on the way, along with my new nikon omega scope. My question is what is the best setup for a base and rings?
What height of rings should I get?
Do I need to take the open sights off?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.