Search results for query: *

I have a few hundred rounds thur my full size sr1911....great gun! had a p97 ...ok! p-90 with the houge grip ..great gun.....sr1911 :) hands down winner imo..

in a large plastic tote with latches that cam over to hold the lid on...I put a EMPD -seal on it and added dryz air to it....... then up on the top shelf in the shop where the temp stays 60 to 70deg 24/7....primers go in 50cal ammo cans with dryz air to ..... still shooting the same Clinton...

I looked this up ...for 1 year to boot! http://www.caradvice.com.au/wp-content/uploads/2007/05/roadtolltable.jpg looks like its time to take away their cars

that clown...sure would like to think the a fellow thr would not think the "the daily clown news" guy is worthy on anything.....

I listen /agree with beck....... a lot more than what else/who else is talking out there.

there not much to be had up here either......BUT there are lots of 6mm bullets to be had ....dam near bought a 6mm rifle just cause of that fact.....then again I loaded up on stuff last oct, as I seen to many folks with there hand out come voting time....imo

wife loves it ....... lite to carry ......i like the little lip u can install on the bottom of the "clip"...my big hand can hang on well...no jamm'.s.. nothing.

remington - 11f , 12ga , 1911 , 101 years old this year....i'd like to say i'm the org owner .... lol

i tossed out blue dot......w296 is fast in my .44 but dirty ...still in the air

the old "Pachmyer presentation" grip has worked for me the gun still rolls ...but i got some big hands...hav'nt found any other grips that work as well (well since the early 90's)

the 250-3000 ,is what all the heavy bullet user's should have bought in the 1st place..:)

u got her rite , as jw is "allways rite" ;)...i have not looked up the spec' on what the 22-250 was worked up from...but it looks to me like folks are trying to find what they already got...

I see alot of folks trying to get a 70+ grain bullets in a .223/22-250. when you could jump to another caliber and just shoot the "low end" of that round,........"as fast as u could push them" ,AND still hit something was the "motto" was it not? :banghead:

Remington Model 721 30/06 he gave it to me, and now i don't have either..:(

yup,,, u had no powder in that round. BTDT

ok i had enough of here say... and called them today ...i was only looking at the .224 bullets 22/250... there all match grade!...(they watch there p's and q's)...." target ones" have a smaller "hp" then the varmit ones a bigger hp to expand faster....other than that they are the same.! ..last...

well, here we go .. I take a "xgrain round" ,start at 1gr below max(by the book!.. that we all buy/have!) and come up with a "powder match" , then i well work up, the real numbers/chambers cut long and/or short ..a starting point is needed......... after this we /i work on the length...

KAHLES 4 x12 mz for 725$ ,to my house ... is what i got ...thanks u all..

This what a poll last month/from a Alaskan site came up with.. View Poll Results: favorite "all around" big game hunting rifles in Alaska? This poll will close on 01-29-2010 at 21:32 .30-06 127 21.34% 7mm Magum 33 5.55% .300WM 162 27.23%...

twofifty... a old and 'mean' gunsmith said go this route, even add a few more rounds to the mix......this was about "all the same size ,trimed /cleaned rounds i had for a small test." hell the gun aint here yet.. ( i have 400+ fed rounds ready to load ) but was looking for a small test...