Concealed carry revolver choices

[Universal]

Again, thanks for all the suggestions. I am still thinking the 637 or 642, however I think I need to find one to try. The idea of the 640 is very valid due to the extra weight. I think it would be pretty easy to find a range with a model 60 to rent.

Not to change the subject but in your picture, Brian Williams, your 65 has orange on the front sight but it does not appear to be an insert. Is that paint? I have been looking for someway to make the front sight on my model 15 more easier to see.

 

[Brian Williams]

Yes, it is Construction marking paint. The kind that you turn upside down and spray the ground to mark where you want things to be on a construction site.

It works very well and I refresh it about every 6 months or so. I spray it on a block of wood that has some on it from previous times and let it sit a moment to let it set up a little and soften some of the paint on the block from before, then I use a toothpick or a nail to put it on the front sight, wipe off any excess and let it dry.
It works great with the white paint I have applied to the rear or grip side of the rear sight.

 

[MillCreek]

In regard to painting the front site, I have also had good results with Testor's acrylic model paint. I apply it using a thin flat-end brush. It does come off from holster wear after a few months, so I reapply it. I suspect that my 99 cent bottle of paint from Wal-Mart will last approximately two of my lifetimes.

Other people have reported good results using the Testor's enamel paint markers, which work like a broad-tip felt marker. I prefer the bottle since my favorite sight-paint color, flourescent green, only comes in the bottle. I apply a flat white undercoat to the sight blade first.

If you wish to change the sight color, the paint can be easily removed by a number of solvents. I know that Hoppe's # 9 will remove it.

 

[rickr44318]

C/C Revolver

Howdy, Universal. Due to similar wrist/elbow and "ergonomic" factors, I looked at J-frame Smiths and equivalents a year ago; finally took a recommendation for a S&W 642 and have not regretted it. I personally prefer the Smith's push-me cylinder release to the Colt's pull-you, and the Taurus is just too chunky (as on a boat or a woman, good lines count). To me, the Ruger was a good choice for a holstered or house weapon, but a bit too bulky for a pocket gun. I got mine for $367 at a show in Richmond. Not wild about the trigger lock, but these are the times ...

I think the 642 typically comes with stubby squared boot-grips; these can be replaced for $20 with the rounded, 1-inch longer Uncle Mike's Combat grips or pricier custom grips. Balance is good, it's fun to shoot (especially with the combat grips), and inside 10-12 yards my accuracy is sufficient. Extra rounds are easy - I carry a speed strip in each coat/jacket and a bullet pouch in the car. In a pocket holster, it fits very nicely in my Columbia coat pocket or even the front pocket of my Dockers (not so great in jeans); if you want to wear "out," you've got many holster choices.

Shop around, test-drive if you can, but I think you'd be pleased with the 642. Good luck, and stay safe. r/

 

[71Commander]

What a bunch of sissies. Everyone knows that us manly-men use fingernail polish on the front sight.

 

[medic_guns]

Colt Detective

You could choose the Colt Detective Special 2". This one is my latest find. I need to pick up some new grips for it this week.

 

[Richard]

I really like the S&W M325 45acp I own. The only concern I have is with the finish. I have read a lot of posts about flaking. I called S&W and I was advised it is a clear coat coming off. I was advised to avoid strong cleaning agents and to use Never-Dull. Here is a picture of mine and it is a joy to carry and shoot. Regards, Richard

 

[Universal]

Well, the CCW bill being proposed in my homestate will now be held over until next year so my gun buying plans have changed. I really appreciate all your advice and opinions.