could you please double check this for me?

[mp2go1]

hello,
im just getting back into reloading and ordered a bunch of things to get started again. i already have the rockchucker supreme loading kit. im basically going to load for 9mm, .45acp(on the progressive), .223, and .308(on the rockchucker, and maybe on the l-n-l). this is what i ordered just for the 9mm and .45 so far based on what ive been reading on what was needed. i would like to have everything set up so that caliber changes would be quick and painless.
1. hornady lock-n-load ap press
2. hornady 9mm dies
3. hornady .45acp dies
4. #1 shell plate
5. #8 shell plate
6. #1 shell holder
7. #8 shell holder
8. 10 pack of l-n-l bushings
9. 2- bullet micro seat stems
10. extra hornady powder measure
11. l-n-l handgun metering assembly
12. rcbs lock out die
13. Hornady Quick Change Powder Die
14. Hornady Quick Change Powder Die Powder Through Expander 355 Diameter
15. Hornady Quick Change Powder Die Powder Through Expander 451/452 Diameter
16. Hornady Lock-N-Load Powder Measure Micrometer for Handgun Rotor and Metering Assembly
17. Frankford Arsenal Vibra-Prime 3 Package of Primer Trays
18. Frankford Arsenal Vibra-Prime Automatic Primer Tube Filler
19. Frankford Arsenal Vibra-Prime Small Primer Tubes with Adapters 3 pack
20. Frankford Arsenal Vibra-Prime Large Primer Tubes with Adapters 3 pack

does that pretty much have everything covered? did i get too much or too little? any help is appreciated. thank you very much.

 

[nicholst55]

Have you got a case trimmer, deburring tool, and something to clean primer pockets with? And a scale?

 

[RustyFN]

A caliper is a must but it doesn't have to be expensive. I am not familier with the Hornady equipment. Isn't the powder through expander die part of the die set, it sounds like you might be buying two. I own Lee and it comes included in the die set. Other wise it sounds pretty good to me. As far as pistol you won't have to trim or debur the brass. Some people will say to clean primer pockets and some won't. I don't clean primer pockets for pistol and haven't had any problems yet. Hopefully Dave or one of the other Hornady guru's will see this and they will be able to give you a little better advice on the press parts.
Rusty

 

[The Bushmaster]

Manuals

Manuals...I never see manuals on these lists. You need at least two. Access to the internet is also a plus.

 

[earplug]

RCBS Lock out die

I use them. Found it easier and faster to buy one for each of my standard loads. .38 spl and .45 ACP.
They are a bit tricky (time consuming) to set up. I really like them. Every now and then I test a double charge or a empty case. They really do work and make phone calls, kids visiting or spouse questions less of a stresser.
They won't cure stupid.

 

[robctwo]

Lee factory crimp die for both .45 and 9mm. Maybe for .308 and .223 if you are shooting auto-loaders. Why are you getting an extra powder measure?

 

[dodgestdshift]

A bullet puller to correct errors, and when adjusting the seater die.

 

[The Bushmaster]

Yup...Dodgestdshift is right. An eraser is an important item when starting out...You will make mistakes at first and later on...

 

[strat81]

+1 to the bullet puller, manual, and caliper recommendations. Don't forget safety glasses too!!

 

[mp2go1]

thanks everyone

first of all, thank you very much everyone for your help.
i already have a dillon caliper, the scale from the rockchucker kit, a speer reloading book, a frankfurt arsenal bullet puller, flash hole uniformer, primer pocket brushes, deburring tool, safety glasses, and a hornady case trimmer(thinking about ordering a giraud or dillon powered model).

and now for the new ?s if you dont mind.....
are there any other manuals/books in particular you recommend?

do the lee factory crimp dies fit the hornady lnl bushings? i have read that they are too short, but some people have made them work by filing them to clear the wire.

do i only need one powder measure? would it be easier to just have two already dialed in, or just one and adjust the charges with the different calibers?

i wasnt really sure about the powder through expander dies? from what i understand, ive read on here that some people recommended to get one for each caliber to charge powder and expand the case at the same time to save a step to have an extra hole for the lockout die or factory crimp die. please correct me if im wrong.

 

[g5reality]

I'm thinking of getting into reloading. Can you share how much the initial investment is for a complete setup? I will be reloading .38, .357, .9mm, .45ACP, .308 & 30-06. maybe even .223.

Thank you

 

[The Bushmaster]

The Sierra 5th edition second printing and the Lyman 48th edition are excellent choices for additional loading manuals...They make a good choice because the Sierra manual is a bit hot and the Lyman manual is a bit conservitive in their load tables.

 

[apachejack]

Your question of getting too much stuff for reloading should be deleted in case a wife sees it. Nobody has too much reloading stuff. As far as the books go, I usually get the one for the typed of bullets I use or the free ones from the powder companies that I use. If neither of those have the loads I want then I go elsewhere. There is tons of info about reloading on the net but above all be careful. And have fun with it.

 

[mp2go1]

thanks again

for the recommendations on manuals/books. i ordered a few yesterday.

g5reality,
as for initial investment, i put aside a grand (may cost more or less)to get quality equipment. im not really worried about spending money on reloading as it will come back in allowing me to shoot more rounds for the same $$ as buying loaded factory ammo. in turn becoming a better shooter, and any extra $$ saved will be used to take other shooting classes to better my skills. besides, most of the money could be recouped if you decide reloading is not for you.

 

[1911user]

I would remove the extra powder measure. You really don't need it unless you want one mounted on the press and another mounted on the bench.

I would add hornady taper crimp dies for 9mm and 45. They require no mods.

Except for the basic vibra-prime, the extra tubes and trays aren't that helpful. Most people just use 1 tube and fill then empty it each time you want to add primers to the press. The LNL-AP will come with 1 large and 1 small primer pickup tube.

 

[RustyFN]

I'm thinking of getting into reloading. Can you share how much the initial investment is for a complete setup? I will be reloading .38, .357, .9mm, .45ACP, .308 & 30-06. maybe even .223.

It depends on your needs. I have the Lee Classic Turret and can load 200 rounds per hour pistol. I can load 1200 to 1600 a month easy and that is enough to keep me shooting in all the matches I shoot in. The setup cost me $207 with one set of dies, you can buy them cheaper now because of the kits available. Each new caliber will cost around $25 for dies and $10 for a turret. IMO this is a great way to go if you don't need thousands of rounds a week or only have one hour a week to load.
Rusty

 

[Shoney]

Why are you ordering items #6 and 7, shell holders. They are not for use on the LNL AP, but will work on a single stage press. The shell plates are for the progressive LNL and are all you need.

Yes to strat81

If you did not purchase a stuck case remover with your RCBS gear, you should get one (primarily for bottleneck cartridges). We all stick cases sooner or later :banghead: and it is nice to have one on hand when you do .

 

[mp2go1]

thank you

1911user and shoney,
thats the info i was looking for. those items were just removed from my order and the taper crimp dies and stuck case remover were just ordered. i appreciate you help. thanks again.