Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
You are using the old Black Responsive theme. We have installed a new dark theme for you, called UI.X. This will work better with the new upgrade of our software. You can select it at the bottom of any page.
I'm poor now, so I just do 100 rounds, but now I haven't changed carry ammo for a while, so I'm sitting a little higher (another digit) but were I to switch, and I recently did for one particular handgun (to ranger bonded 147s), I would start the trust at about 100 rounds of care-free shooting.
Personally, I'd shoot carry ammo until I could shoot 200-300 in a row without a single problem.
The reason I don't is due to cost. Some might say, "well how much is your life worth?" to which I say, "all of the money I have".
Realistically, I'll shoot 250-500 rounds of FMJ through it to "break it in", then buy 150 rounds of carry ammo and shoot it up until I have just enough left to fill a couple mags and the chamber.
In all seriousness, it depends on the make and model. Kimbers are recommended to have several hundred rounds fired just to "break it in". My Colts have never failed, and they never had to have a break-in. My Glocks have never failed, and they too required no break-in-period. For me, if my Colts and Glocks go the first 100 rounds with zero failures, I trust them...and Colts and Glocks are all I carry. The other note to add is that I never carry a single pistol. I always carry at the least, one back up of identical configuration and caliber with interchanging magazines.
I usually run 200 rounds of FMJ ammo through a gun, and then maybe 50 rounds of the JHP ammo before I consider it reliable for carry.
I know 50 rounds isn't all that much to ensure reliability with your carry (usually JHP) ammo, but anything I'd shoot would get expensive (Gold Dots or Federal HST).
*edit* I recently bought a new LCP too. I've put about 100 rounds through it, and it already broke. Sometimes the hammer doesn't drop when you pull the trigger! Maybe 300 rounds isn't such a bad idea...I'll have to start the count over again once Ruger fixes it and I get it back.
i vote for 200 as well. it takes a while for metal to wear in.what you are really doing is wearing off all the high / tight spots in the action. so everything moves easilly and smoothly. get a rough or tight spot and a little tiny spec of dirt and it could cause a jam at a most inoppertune time.
Shoot enough to get the weapon good and hot. Shoot enough to know how the weapon is going to react every time. Shoot enough to know how you are going to react with every shot. For every person this is different. With me and with a new weapon it takes about 200 rounds. Also and it may be expensive but shoot the ammo you intend on using as your personal defense ammo.
When my Kimber was brand new, I ran 200 Hydra-Shoks through it. No problem. Recently, after about 10000 dounds, I fired all of my old Hydra-Shoks and 200 HSTs through it. No problem.
Keep in mind, 200 rounds is enough to force you to use different magazines. I'm not anal enough to track lot numbers, but I will buy the test ammo from different locations. During the test, I will also shoot with the weak hand, one-handed with both hands, emergency and tactical reloads.
How about for a used pistol? Assuming you replace all the usual things (recoil spring, firing pin spring, mag springs and followers, to be thorough) would most people be happy with 100 or 150 of hardball followed by 50 of JHP? I figure if it is good for 150 to 200 rounds in a row, getting dirty, and still does the job, it should be ok.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.