Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Lubricating Ruger Mk III to prevent misfeeds?

Discussion in 'Handguns: Autoloaders' started by Arrogant Bastard, Aug 28, 2008.

Thread Status:
Not open for further replies.
  1. Arrogant Bastard

    Arrogant Bastard Member

    Joined:
    Apr 3, 2008
    Messages:
    357
    Location:
    Houston TX
    I recently bought a Ruger mk III Hunter.

    Took it to the range already, twice, and fed about 550 rounds through it each time.

    Both times, field stripped it per the manual and reassembled.

    Both times, it fed the ammo very well -- perhaps one jam per box of 550.

    Today, took it again to the range.

    Had a devil of a time with it. Often, it would not strip the top round from the magazine on the first try -- sometimes had to eject and retry numerous times. Many times, it damaged the round attempting to feed it.

    This is very much not the character it displayed the first two times I took it to the range. I am wondering if there is a part I should pay special attention to while cleaning, or perhaps if it needs lubrication.

    The manual did not state where it needs lubrication.

    Any suggestions?
     
  2. RickW

    RickW Member

    Joined:
    Jul 17, 2008
    Messages:
    85
  3. wingman

    wingman Member

    Joined:
    Dec 24, 2002
    Messages:
    2,185
    Location:
    texas
    You may have a problem other then lube however FP-10 on small parts
    and gun butter on slide of my MK2 speeds up the process big time.:)
     
  4. RickW

    RickW Member

    Joined:
    Jul 17, 2008
    Messages:
    85
    On the Ruger site you will find a video on cleaning the Ruger MK3. It will show you where to lube the pistol.
     
  5. tlen

    tlen Member

    Joined:
    May 12, 2008
    Messages:
    526
    Location:
    Kansas
  6. Arrogant Bastard

    Arrogant Bastard Member

    Joined:
    Apr 3, 2008
    Messages:
    357
    Location:
    Houston TX
    1st time: Federal copper plated -- no problems

    2nd time: Remington Golden -- No problems

    3rd time: Remington Golden -- several problems
     
  7. tlen

    tlen Member

    Joined:
    May 12, 2008
    Messages:
    526
    Location:
    Kansas
    Remington ammo is noted for FTE and leading problems and is not recommended on the GunTalk-Online.com site. I've had good results with [cheap] Federal 550 round value packs from WMT in my MKIII678.
     
  8. JDGray

    JDGray Member

    Joined:
    Sep 16, 2005
    Messages:
    5,131
    Location:
    SW MI.
    Be sure your mags are firmly seated, sometimes they seat hard. I've solved all my extraction issues with a Volquartsen Exact Edge, extractor.(When you get them)
     
  9. wally

    wally Member

    Joined:
    Jan 2, 2004
    Messages:
    12,347
    Location:
    Houston, Tx
    I have had several boxes of these where instead of climbing the feed ramp, the bullet "folds" at the case mouth causing a feed jam. That and the relatively high dud/misfire rate caused me to quit buying these, although they give very vew problems in my Neos which has a straighter feed path and a heavier firing pin hit.

    --wally.
     
  10. RickW

    RickW Member

    Joined:
    Jul 17, 2008
    Messages:
    85
    I used Remington Golden the very first time out with my MK3 Target. I had a devil of a time with failure to feed and duds. I did nothing different other than change my ammo to Federal Champion (510) and the problems went away. I would try the Federal ammo again and see what happens.

    Guntalk is a wealth of information for owners of the MK type Rugers.
     
  11. PO2Hammer

    PO2Hammer Member

    Joined:
    Nov 30, 2003
    Messages:
    3,234
    Location:
    MINNESOTA
    Cleaning the magazines is a critical part of Mark II/III maintenance. That might not be your problem, but the bullet lube builds up on the front inside edge of the mags where the bullet noses rub. Then they don't come to the top of the mag smoothly.

    I even lightly oil the inside of the magazines. Since I don't keep them loaded, I don't worry about oil ruining the ammo.

    My new Mark III hunter has had a few failures to fire with Rem. bulk ammo, and a couple time they didn't extract, otherwise it's been pretty darn good.

    Anything other than Rem. bulk ammo and it runs fine. Now that I have about 1K rounds through it, it will even cycle subsonics.

    I like to use plenty of FP-10 oil.
     
  12. KBintheSLC

    KBintheSLC Member

    Joined:
    Jul 30, 2007
    Messages:
    3,197
    Location:
    Stalingrad, USA
    It sounds like you may have reattached the lower grip frame to the upper receiver a little crooked. I have done this once before. The tolerances can vary a tiny bit, allowing the slightest bit of "canting" between the upper and the lower. It can be off by the tiniest amount and may be unnoticeable to the naked eye, but it will throw off your feed angle and create a chain reaction of failures.

    I doubt it is an ammo issue since you had no problems with the same kind of ammo once before. I would strip it down again, and make sure it is perfectly straight. BTW, the MKIII Target that I own is not ammo sensitive at all... yours should chew up most every type of cheap stuff.

    Besides that, I generally lube the bolt and the inside of the receiver with an oily patch, then wipe off the excess with a dry patch (it does not need lots of oil). The rest only needs a wipe with a silicone cloth.

    Best of luck. This is a great gun which I am sure you will enjoy.
     
  13. 3KillerBs

    3KillerBs Member

    Joined:
    Apr 28, 2008
    Messages:
    993
    Location:
    NC Sandhills
    My Mark III hates bulk pack Remington. I get a misfeed every other magazine or so. Which is particularly annoying because the bullet tends to get hung up partway in the chamber and partway in the magazine so it takes a bit of doing to get the magazine to drop so that the jammed bullet can fall free.

    Same with the the .22/.45's DH and I borrowed for our concealed carry class.

    Even the bolt action rifles don't like that stuff and won't extract it reliably.

    Try the Federal or the Winchester white box instead.
     
  14. glockman19

    glockman19 Member

    Joined:
    Mar 16, 2007
    Messages:
    3,699
    I have had NO problems with CCI Blazer, CCI mini-mag, high velocity & standard velocity 40 grain.
     
  15. Comanche180

    Comanche180 Member

    Joined:
    Jan 11, 2008
    Messages:
    142
    Location:
    Maine
    mis feeds

    I shoot a Buckmark and MkII quite a lot. I have had bad results with Remington bulk ammo, duds. I have had excellent results with Federal bulk ammo. I also clean my magazines regularly, 22 ammo seems to be generally dirtier than an centerfire I shoot. I usually clean each gun after 200 rounds, especially the MKII which will fail to extract when dirty. I haven't had trouble with misfeeds in either gun which I attribute to cleaning the magazines.
     
Thread Status:
Not open for further replies.

Share This Page