Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

New barrel for Savage 10

Discussion in 'Rifle Country' started by 45shooter, May 29, 2013.

Thread Status:
Not open for further replies.
  1. 45shooter

    45shooter Member

    Joined:
    Jan 8, 2004
    Messages:
    262
    Location:
    USA
    I picked up a cheap Savage model 10 FP in .308 Winchester from a co-worker yesterday. The bad news is that the barrel is no good as it has rust and corrosion in the bore and outside as if it had fired corrosive ammo and didn't clean it (is there corrosive .308 Winchester ammo?). The good news is that rest of the rifle is in good condition with decent finish and the bolt looks clean. I paid $120 for it and knew the condition of the rifle going in.

    I want to replace the barrel the of the rifle and change the caliber to .243. Anybody know where I can get a new .243 barrel and where I can have the barrel installed properly? How much will it cost to have it done?
     
  2. joed

    joed Member

    Joined:
    Sep 17, 2009
    Messages:
    2,201
    Location:
    Ohio
    You're probably in luck as I almost went through this 3 years ago. I had a mod 10 in .223 that I wanted to convert to .22-250.

    My mistake was I went to the Savage site and was kind of pushed to custom barrels which weren't cheap. But, you can find Savage or fair aftermarket barrels at reasonable prices.

    So, keep in mind the barrel you want will effect the total cost depending on quality.
     
  3. joed

    joed Member

    Joined:
    Sep 17, 2009
    Messages:
    2,201
    Location:
    Ohio
    You can actually do this yourself if you have any mechanical aptitude. Others will be along shortly.
     
  4. MtnCreek

    MtnCreek Member

    Joined:
    Dec 8, 2010
    Messages:
    3,976
    Location:
    West GA
    Call Jim Briggs at Northland Shooting Supply
    (763) 682-4296

    Also, get his recoil lug and new nut to match.

    Where are you located in USA? If you're near me, I have action wrench and nut wrench you can use.
     
  5. 45shooter

    45shooter Member

    Joined:
    Jan 8, 2004
    Messages:
    262
    Location:
    USA
    I don't want to spend a lot of money on it as it will be my "truck" rifle.
    It will sit behind the seat for days at a time and get pulled out occasionally.
     
  6. brian923

    brian923 Member

    Joined:
    Jul 4, 2007
    Messages:
    676
    Ill be that guy. Best thing to do is... buy a 243 barrel from a known manufacture. Do your homework, pacnor, mcgowen, shilen, and try thebarrelman.com. Everyone offers prefit barrels for savage nowadays. Get a go gauge, and a savage barrel nut wrench from midwayusa.com. you can get barrel blocks if you want but I just made some from some oak I had laying around. If you want. Now is the time to add a precision ground aftermarket recoil lug and new barrel nut if you want. Clamp barrel in vise blocks. Remove old barrel nut. Remove old barrel. Screw in new barrel with old or new nut installed. (Put the recoil lug back on in between the receiver and the barrel nut) now, remove the extractor and plunger from the bolt head. But leave the bolt head on. Chamber the go gauge. Screw the barrel on until it contacts the go gauge. Torque down the barrel nut. Done. Now, if you want to replace the recoil lug with a new one. It probably will not have a locator tab on it. It might be good to buy the little $15 recoil lug locator from midway as well. I went this way because I like to be hands on with my gun projects. It fun, and you can change out barrels whenever you want! Good luck!
     
  7. brian923

    brian923 Member

    Joined:
    Jul 4, 2007
    Messages:
    676
    Well, if you don't want to spend a lot, clean it up and see how It shoots. You may be pleasently suprized. ..
     
  8. Gtscotty

    Gtscotty Member

    Joined:
    Jul 2, 2007
    Messages:
    2,376
    Location:
    Wyoming
  9. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    What he said.

    What it looks like has little bearing on if it will shoot or not.

    And a beater truck gun is gonna lead a hard life anyway.

    rc
     
  10. dagger dog

    dagger dog Member

    Joined:
    Jan 30, 2008
    Messages:
    2,706
    Location:
    SO. IN
    45shooter,

    Brownell's has a good how to Savage barrel swap in their library it's a freebie !
     
  11. adelbridge

    adelbridge Member

    Joined:
    Jan 30, 2012
    Messages:
    1,107
    Location:
    Texas
    eabco.com

    also I just sold a .308 takeoff on gunbroker and it sold for $65, maybe ebay has them too
     
  12. slowr1der

    slowr1der Member

    Joined:
    Mar 25, 2010
    Messages:
    984
    Honestly, if I was looking for a truck gun I'd look for a take off barrel. I see them for $50-80 occasionally. Much cheaper than buying even one of the cheap aftermarkets for $2-300.
     
  13. docsleepy

    docsleepy Member

    Joined:
    Mar 10, 2009
    Messages:
    1,023
    FIRST thing to do is to clean/oil that existing barrel and shoot it to see what it does. I've read threads where people were astonished at how little impact the damage had. I saw one article where people practically took a DRILL BIT to the muzzle of a rifle and it barely affected the groups.....Mosin Nagants go 70 years and even if their bore doesn't look great, they shoot acceptably. The cheapest barrel you are ever going to get is already on that rifle....

    And you got a GREAT deal, BTW. You can't get a Savage receiver for $300 anywhere, you have to buy an AXIS rifle just to get that receiver.

    Please let us know what you find out, no matter what you do. Jim Briggs is great and a cheap barrel is less than $100 if you decide to go that route. Beg or borrow a .308 go gauge and the nut wrench, and read how to adjust, takes just a few minutes. I've done it several times.
     
Thread Status:
Not open for further replies.

Share This Page