The Colt action was known as the "Bank Vault" action due to it locking up the cylinder tightly WHEN THE TRIGGER IS PULLED.
If you simply cock the gun and don't pull the trigger the cylinder won't lock tightly in place.
As above, if the cylinder locking bolt doesn't drop into the locking notch on the cylinder, the action is NOT operating right, whether it left the factory that way or not.
Here's my instructions on how to check an old Colt action for proper timing.
Note that tis covers the older Colt's like the Official Police/Python and the Detective Special/Diamondback.
It DOES NOT cover any of the later Colt's like the Mark III/King Cobra, and it does not cover the S&W/Ruger etc.
Only the old Colt action is supposed to lock up tightly when the trigger is pulled. This is NOT a valid test for S&W, Ruger or any other revolver. They are not intended to lock up tightly when the trigger is pulled.
CHECKING OLD MODEL COLT TIMING
BOLT RETRACTION AND "SNAP BACK".
Open the cylinder and look at the small "lug" in the bottom of the cylinder window. This is the cylinder locking bolt.
Cock the hammer, and watch as the bolt retracts into the frame and pops back out.
The bolt MUST begin to retract THE INSTANT the hammer begins to move.
There MUST be NO (ZERO) hammer movement possible before the bolt starts to retract.
The bolt should retract smoothly with no hesitation until it's fully retracted, then it MUST pop back out with a clean "snap".
There should be no hesitation, and no amount of "creeping" back out.
CYLINDER UNLOCKING.
Close the cylinder.
Use your left thumb or fore finger to again cock the hammer, closely watching the cylinder bolt as you SLOWLY cock the hammer.
As the hammer comes back, the bolt will retract away from the cylinder.
The bolt MUST retract far enough to unlock the cylinder BEFORE the cylinder begins to rotate.
If the bolt is still slightly engaged with the cylinder lock notch, the cylinder will be attempting to turn while still partially locked.
This produces a "catch" or "hard spot" in the trigger pull and will damage both the bolt and the cylinder lock notches.
This often appears as metal "pulled out" of the lock notches, with rounded off and burred notches.
BOLT DROP TIMING.
Continue to cock the hammer, LIGHTLY laying your right index finger on the cylinder just enough to prevent "free wheeling".
Watch for the bolt to drop back onto the cylinder. WHERE the bolt drops is CRITICAL.
The bolt MUST drop onto the leade or ramp in front of the actual cylinder notch.
If the bolt drops too soon, (in front of the notch ramp), it will mar the finish of the cylinder.
The bolt SHOULD drop into “about” the MIDDLE of the ramp.
If the bolt drops late, (farther toward the actual locking notch) the revolver may display "cylinder throw-by".
In this condition, during double action shooting the cylinder may rotate PAST the locking notch, and fire in an unlocked condition.
It's the nature of the Colt action, that a hesitant or jerky trigger pull by the user can induce throw-by in even a properly tuned Colt.
The Colt trigger should be pulled with a smooth, even pull, with no sudden jerks at the beginning.
CYLINDER LOCKUP.
Continue to pull the hammer back and both watch and listen for the bolt to drop into the cylinder lock notch.
The bolt MUST drop into the actual lock notch BEFORE the hammer reaches full cock.
The most common Colt mis-time situation is the hammer cocks before the bolt drops into the lock notch. (Hammer is cocked, but cylinder isn't locked).
In this condition, with the hammer fully cocked, you can push the cylinder slightly, and you will hear the "CLICK" as the bolt drops into lock.
In my experience, most Colt's leave the factory with the bolt dropping a little late into the leade, but usually wear in to correct timing.
If the bolt drops onto the cylinder early, no real problem, but there will be extra finish wear.
If the bolt drops late (closer to the lock notch) the cylinder may "throw by" or rotate TOO far in double action and this can cause off-center primer hits and firing while unlocked.
Each of these checks should be done on EACH chamber. All of these checks are better done individually. In other words, do the bolt retraction check on all six chambers, then do the bolt drop test, and so on.
A properly tuned Colt will:
Have a smoothly functioning bolt with no sticky or hesitant movement.
Unlock before the cylinder begins to turn.
The bolt will drop onto the middle of the ramp.
The bolt will drop into the lock notch before the hammer reaches full cock.
Have a smooth trigger pull, which does "stack" or get heavier as the trigger is pulled.
Kevin.
