Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Portable Handloading Setup--Which One?

Discussion in 'Handloading and Reloading' started by Cosmoline, Jun 13, 2005.

Thread Status:
Not open for further replies.
  1. Cosmoline

    Cosmoline Member

    Joined:
    Dec 29, 2002
    Messages:
    23,648
    Location:
    Los Anchorage
    I'm currently in a situation where I won't be able to set up another reloading bench for some time, but I'd like to work up small batches of custom loads. I've seen the Lee Loader and the Lyman hand press. For batches of 20 rounds or so, which one would be better? Costs are about the same given that I'd need to buy at least two Loaders and could just get the one Lyman hand press. Are there other options? Sadly there's no bench or table I can hook to unless I leave no marks (no bolts through the table)
     
  2. mtnbkr

    mtnbkr Member

    Joined:
    Dec 25, 2002
    Messages:
    3,108
    Location:
    Manassas, Va
  3. Jim Watson

    Jim Watson Member

    Joined:
    Dec 24, 2002
    Messages:
    22,340
    Look at the Midway pedestal mount. It supports a regular press and can be pushed into a corner when not in use. Set components out on any table or counter available. I had a homemade version in small quarters when I first got out of college and it and a folding card table served me very well.

    Otherwise, NOT an orignal Lee Loader.
    The Lee Handloader is ok. The Lyman has the capability of being bolted down for use as a bench press, but I would wonder if that might not make it clumsy to use barehanded.
     
  4. mtnbkr

    mtnbkr Member

    Joined:
    Dec 25, 2002
    Messages:
    3,108
    Location:
    Manassas, Va
    Another idea is to mount your press to a board and use C-clamps to secure that board (and press) to your table or desk. That's how I got started years ago. I've only loaded straightwall pistol cases that way though.

    Chris
     
  5. taliv

    taliv Moderator

    Joined:
    Oct 23, 2004
    Messages:
    22,098
    cosmoline, you need to go to www.sinclairintl.com and get the arbor press and the LE wilson hand dies.

    benchrest quality stuff and you can carry most of it in your pocket.

    if you want to use a small rubber mallet, you don't even need the press to use the hand dies.
     
  6. 1911 guy

    1911 guy Member

    Joined:
    May 5, 2005
    Messages:
    6,380
    Location:
    Garrettsville, Oh.
    Lee Loader

    is very rudimentary. It works, as I've got one for my .357, but I haven't used it in a long time. I would get the hand press if I were to do it over. You'll have much more control over seating depth, crimp and some other things the Lee Original does not allow much control over. Also requires no mallet.
     
  7. JNewell

    JNewell Member

    Joined:
    Oct 1, 2003
    Messages:
    2,714
    Location:
    Land of the Bean & the Cod
    The Lee hand press is cheap and uses standard dies -- very portable, too. Hard to beat for its intended purposes. Costs hardly more than a Lee Loader or two!
     
  8. Vern Humphrey

    Vern Humphrey Member

    Joined:
    Dec 30, 2002
    Messages:
    18,507
    Location:
    Deep in the Ozarks
    I spent a year and a half in Darkest Michigan, working a project for General Motors and living in a 2-bedroom apartment. I used a Lee hand press, and had everything I needed to load .45 ACP, .38 Special/.357, .22 Hornet and .30-06 in a tool box in the closet.
     
  9. ocabj

    ocabj Member

    Joined:
    Jan 22, 2003
    Messages:
    2,383
    Location:
    Riverside, CA
    Sinclair Intl recently added a wood stand to their catalog that you mount your single stage press to.

    http://www.sinclairintl.com/cgi-bin/category.cgi?category=search&item=09-820&type=store

    It looked nifty, so I copied the idea to build one for myself.

    [​IMG]

    I pretty much went off of the photo for the basis. I didn't have any specifications of the actual product or anything.

    Seems sturdy enough. I even neck brass on this setup.

    I figure I can keep my Rockchucker mounted to this thing and it will allow me to take it to the range if I need to. This is my primary rifle reloading press. I use my Redding T-7 for pistol.
     
  10. roo_ster

    roo_ster Member

    Joined:
    Oct 2, 2003
    Messages:
    2,980
    Location:
    USA
    I own a Lee Handloader from my apartment days. It had enough ooomph to reload .357mag. I would recommned Hornady One Shot case lube for decapping/resizing.

    Dies, RCBS hand primer, and a set of Lee dippers finished off the equipment list.
     
  11. blackhawk44

    blackhawk44 Member

    Joined:
    Apr 27, 2005
    Messages:
    29
    Location:
    Republic of Texas
    Get an lightweight aluminum (Lee) C or O press. The little C press can be had for less than $20. Mount to a board and c-clamp to a table. Mounting so the board goes across the table allows clamping both near and far sides and adds much to rigidity. Much less fatiquing than either "hand" press. Banging on an original Lee Loader get tiresome very very quickly.
     
  12. lee n. field

    lee n. field Member

    Joined:
    Dec 29, 2002
    Messages:
    3,731
    Ditto to the people who have been recommending the Lee Hand Press.

    Cheap, they use standard dies. Extremely portable. The ergonomics are kind of sucky, and you won't have enough leverage to resize larger rifle brass unless you're pretty strong.
     
  13. bogie

    bogie Member

    Joined:
    Jan 2, 2003
    Messages:
    9,569
    Location:
    St. Louis, in the Don't Show Me state
    I'm gonna differ here - and I own a Lee hand press.

    Get an RCBS Partner press, bolt it to a 2x6, and clamp that to whatever. The Partner can deal with most cartridges, and is nice enough on tolerances that you see a lot at benchrest matches. I'd also use an arbor press (mallet bad) and Wilson seater. Get Redding FL resizing dies, but don't worry about their seaters. You can put EVERYTHING you need in a toolbox/tacklebox.

    Hey, are you talking about rifle or handgun? If handgun, I'd go completely different.
     
  14. candt

    candt Member

    Joined:
    Jul 13, 2004
    Messages:
    59
    What is an arbor press? Anybody have pictures?
    For my portable setup, I have a Lee challenger press mounted to a piece of wood that I can clamp to a table anywhere. Nice and sturdy when clamped too. I also have a Lee powder measure mouted on a similar size piece of wood that I can bring with me anywhere. I also own a Lee Loader, and it works but it is loud.
     
  15. ocabj

    ocabj Member

    Joined:
    Jan 22, 2003
    Messages:
    2,383
    Location:
    Riverside, CA
  16. milanuk

    milanuk Member

    Joined:
    Feb 9, 2004
    Messages:
    72
    Location:
    Wenatchee, WA
    I've been using a couple of the Lee Loader C-presses for various light duty applications... portable press for a bullet seater to take to the range (w/ some O-rings to help float the die and the shell-holder, it works extremely well), as well as for mounting a collet type bullet puller. I have them bolted to some blocks of wood, and then C-clamp the wood to my bench (or wherever I'm working). I have tried some light F/L sizing w/ them, and there was just too much flex and variation in measured headspace dimension, even in .223 Rem w/ a lot of lube!

    I'm getting set up to load for 6mm BR, and while I should have enough brass to get me by for most matches I'll be entering (200 pcs), even multi-day ones, if this rig ever gets hauled out varmint hunting I might be in trouble after a day (or less!). I'd picked up some Wilson dies for my Hart arbor press; the biggest concern was whether or not I'd need a body die regularly (some say they only use it every 4-5 firings, some every time, which pretty much mirrors my experiences). I decided to try the Lee hand press and see how that works out. If it doesn't... I'll have a handy little bullet seater for the range, I guess ;)

    Also, another option for a small portable loading station while you are moving could be to get a single or double thickness of 3/4 ply of an appropriate size, screw-n-glue them together, and bolt a 2x4 cleat to one side in the middle... and then clamp it in a Black & Decker WorkMate, using the 2x4 cleat to clamp btwn the jaws. Might be kinda low to the ground, but pretty damn sturdy. I'm looking at moving sometime here in the (somewhat) near future, depending on a lot of things, and I think I know how my Dillon 550 and Redding M25 will be mounted...

    HTH,

    Monte
     
  17. candt

    candt Member

    Joined:
    Jul 13, 2004
    Messages:
    59
    Heres a picture of my bench in my apartment. Quite heavy with all of the components on the bottom shelf. It works very well.
     

    Attached Files:

  18. threefeathers

    threefeathers Member

    Joined:
    Jun 5, 2003
    Messages:
    1,176
    Location:
    AZ
    Let me suggest a Lyman T-Mag turret. I started with the little RCBS Partner Press, and now have it, the T Mag and an RCBS Pro 2000 ll on my bench next to each other.
     
  19. Cosmoline

    Cosmoline Member

    Joined:
    Dec 29, 2002
    Messages:
    23,648
    Location:
    Los Anchorage
    Wow, thanks for all the options! Candt--where did you get that bench?
     
  20. bogie

    bogie Member

    Joined:
    Jan 2, 2003
    Messages:
    9,569
    Location:
    St. Louis, in the Don't Show Me state
    That's a Black & Decker Workmate - they sell 'em at Home Depot and Lowe's...

    IMHO, they take up a lot of room, even when folded. Again, I'd recommend a toolbox and c-clamp approach.
     
  21. pete f

    pete f Member

    Joined:
    Dec 7, 2004
    Messages:
    1,793
    If you are going to be in an apartment, There are several options and ways to look at ways to do this.

    DO you need to completely pack it away and keep it discrete as in living with other roommates?


    Is your requirement one of just space?

    For a long time I live in a tiny house and with a wife and two kids. My reloading was restricted to what I could fit in one rubbermaid tub. I ended up with a dillon SDB for pistols and I used a Lyman turret head press for rifle stuff. I got a couple of layers of 1/2 inch plywood screwed together to make a base and this just got clamped to the kitchen counter. I thought real hard about making it as efficient as possible, both in space and time. obviously being clamped on the kitchen counter, it had to be put away after a couple of hours at most.

    I found that with this set up I could be in action in ten minutes and the SDB allowed a hour of work to put out 3 or 4 hundred rounds. This is the hard part. if you go with a hand die or a portable set up, they are designed for maybe making 20 rounds or so at a sitting. The sinclair stuff is top notch, absolutely the best quality, but it is designed for guys in bench rest matches where they load five shots at a time. Not designed for production loading. If you are looking like i was for being able to make blasting ammo, then Do Not Go with the handheld or the like. Later I bought a grinder stand and used that as tool stand and just kept the dillon press on the stand down stairs next to the washer. I bought a couple of bags of shot and filled the base with 50 pounds of shot to stabilize the whole works.
    this is similar to what i had,
    http://www.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=7240

    another option I have had experience with is using table bases, these are often available really cheaply. I have used some similar to these...

    http://www.kpetersen.com/1page7tablebasepricelist.htm#bartables

    http://www.kpetersen.com/1page7tables.htm
     
  22. candt

    candt Member

    Joined:
    Jul 13, 2004
    Messages:
    59
    My bench is by no means the most portable, just an option for apartment dwellers. My bench I got at Sears, and it is the Craftsman brand of the workmate type bench. I couldnt be happier with it.
     
  23. lee n. field

    lee n. field Member

    Joined:
    Dec 29, 2002
    Messages:
    3,731
  24. ocabj

    ocabj Member

    Joined:
    Jan 22, 2003
    Messages:
    2,383
    Location:
    Riverside, CA
  25. taliv

    taliv Moderator

    Joined:
    Oct 23, 2004
    Messages:
    22,098
    lee and candt

    keep in mind with the arbor press/wilson hand dies, you're usually using collet style dies and only "neck sizing" about 1/4" of the case. and with the wilson dies, you've got to pick the size of the collet you want, and they come in .001" increments, allowing you an extremely precise control over neck tension, but also requiring you to have some clue about how much you want. i.e. it might not be the best choice for someone starting out.

    the lee hand press stuff would be more appropriate if you want to full-length resize.


    my opinion is that the arbor press/wilson dies are much, much higher quality than anything lee ever made, but it's not really appropriate for every situation. if you're just making blasting ammo, then go with the lee... not because of the expense, but because you're probably full-length resizing.

    again, the head on the arbor press, as you can see in the picture, is held in place with essentially a little bit of friction applied by the black lever. if you tried to full-length size a bottleneck brass case that had expanded significantly, the head would probably just slide up and scratch the post. it's no rock chucker
     
Thread Status:
Not open for further replies.

Share This Page