Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Small AK problem, please help.

Discussion in 'Rifle Country' started by 7.62shooter, Nov 7, 2008.

Thread Status:
Not open for further replies.
  1. 7.62shooter

    7.62shooter Member

    Joined:
    Oct 20, 2008
    Messages:
    35
    I just picked up my new polish underfolder by Allied Armament today and let me start off by saying it is badass. But there is one problem. The magazines will not lock all the way into place, and some of them will not lock into place at all. I have assessed that the problem is that the latch which locks it into place and is depressed to remove the mag is just a hair too long at the top so the part of the mag that locks into the latch is keeping it from locking in all the way. If i could just make it a bit shorter it would be able to completely lock up. So... Is the only way to fix that just someway to file it down? And if so how would one go about doing that? I dont know how i could remove the latch from the rifle so i would just have to do it on the gun and the space to get the file in there is very small... Any thoughts? Thanks.
     
  2. Hk91-762mm

    Hk91-762mm Member

    Joined:
    Dec 27, 2007
    Messages:
    415
    Location:
    western NY
    Let me off this advise --WE on the web cant see the gun --I suggest you take it to a gunsmith [one who likes EBRs+aws] and have them take a look!
    If you need to file down a part you should remove it and put it in a vise where you can see what you are doing
    Do any mags fit?? If so you are only a few thou. off tollerences and maby it will break in as you work the mags back and forth
     
  3. MIL-DOT

    MIL-DOT member

    Joined:
    Jun 20, 2006
    Messages:
    3,110
    Location:
    Georgia,C.S.A.
    Sounds like you need to file the mag catch, like when converting a Saiga. Get a diamond tipped Dremel bit, about $9 at Lowes. Have someone hold the rifle stable and vertical for you, and grind the top the the mag catch lever. The steel is very hard, you won't screw it up quickly, just stop and check the fit with a mag every little while.
     
  4. 7.62shooter

    7.62shooter Member

    Joined:
    Oct 20, 2008
    Messages:
    35
    ok thanks for the info guys. Yes a few of them do fit, but it still does not click and lock all the way.
     
  5. Sepia

    Sepia Member

    Joined:
    Nov 3, 2008
    Messages:
    41
    Location:
    Tampa FL
    Just take it slow with the dremmel. The last thing you want is to find out that none of the mags will lock into place.
     
  6. Gord

    Gord Member

    Joined:
    Jul 19, 2006
    Messages:
    3,829
    Location:
    Behind enemy lines
    My Yugo underfolder needed a bit of filing to fully lock mags - was a bit of a surprise to me, but after thirty seconds of filing it's fine now.
     
  7. DoubleTapDrew

    DoubleTapDrew Member

    Joined:
    Feb 23, 2006
    Messages:
    5,356
    Location:
    Oregon
    My Vector (polish) does the same thing with about 4 mags, other ones fit fine. I would check other mags before you go filing away at your gun, and possibly file those mags instead of the rifle. You don't want to find out you had a couple out of spec mags and then have a problem with mag wobble when you get more magazines that are in spec.
     
  8. J32A2

    J32A2 Member

    Joined:
    Feb 25, 2007
    Messages:
    69
    Location:
    Phoenix
    Where did you get it if I my ask?
    I just picked one up, my 1st AK, you are right, it is badass!!!
     
Thread Status:
Not open for further replies.

Share This Page