I'm considering the purchase of one of these repro revolvers and was wondering if anyone has any comments or advice on them. Are they accurate? Durable? I know they are expensive, but that's about all I can find out about them. I really like the design but don't want to spend the money if they lack accuracy and/or durability (of course, as compared to other BP revolvers). Any comments would be sincerely appreciated.
The Lemat revolver
- Thread starter Dithsoer
- Start date
- Status
Tommygunn
Member
I've had a Le Mat for 15 years. They're made by Pietta and they seem well-made. The hammer is checkering rather than the parallel striations that Pietta normally uses. Mine is pretty accurate.
Two downsides I've noticed:
(A.) For me, the way the loading lever/plunger is arranged isn't as ergonomic as the Colt/Rem/others design. Pulling up just seems odd, to me.
(B.) The lever is somewhat bendable. I bent mine a little. No big deal. In fact I think either Navy Arms or Dixie Gun Works carries replacements due to this.
Keep in mind, of course, it will take longer to load 9 chambers
than 6.
The revolver has a adjustment on the right side of the frame that, IIRC, times the locking bolt, which on mine needs minor adjustments from time to time. The bolt on this gun protrudes from the rear of the frame into a hole in the heel of the cylinder (just so you know it does have one).
They are interesting revolvers and I believe they were favored by Jeb Stewart's Cavalry during the Civil War. Didn't help ol' Jeb against George Armstrong Custer, much...though
Two downsides I've noticed:
(A.) For me, the way the loading lever/plunger is arranged isn't as ergonomic as the Colt/Rem/others design. Pulling up just seems odd, to me.
(B.) The lever is somewhat bendable. I bent mine a little. No big deal. In fact I think either Navy Arms or Dixie Gun Works carries replacements due to this.
Keep in mind, of course, it will take longer to load 9 chambers
than 6.The revolver has a adjustment on the right side of the frame that, IIRC, times the locking bolt, which on mine needs minor adjustments from time to time. The bolt on this gun protrudes from the rear of the frame into a hole in the heel of the cylinder (just so you know it does have one).
They are interesting revolvers and I believe they were favored by Jeb Stewart's Cavalry during the Civil War. Didn't help ol' Jeb against George Armstrong Custer, much...though
Last edited:
Like tommygun says. dixie does catalog the loading lever parts and some others. VTI has been able to back order parts from italy as has taylor while others have not been able to get Pietta to send parts. Recently, VTI has begun listing the LeMat Parts on their site. I wrote to ask if that meant they now have a domestic supply but they did not answer. The LeMats are well made and accurate in the revolver mode the loading lever system tends to bounce up out of the detent and the shotbarrel presents problems as to reliable ignition.
One-hand "Duelist"
They are not usually commonly seen but this weekend I saw at least 4 of them at the Dallas Market Hall gunshow.
One-hand "Duelist"
They are not usually commonly seen but this weekend I saw at least 4 of them at the Dallas Market Hall gunshow.
Last edited:
I own the Navy model LeMat
and it is the proudest gun I can ever own.
Just look at the case hardening on the hammer and trigger after you wiped it down with protective grease, and just admire the look of radiant health on all the metal and wood parts.
and it is the proudest gun I can ever own.
Just look at the case hardening on the hammer and trigger after you wiped it down with protective grease, and just admire the look of radiant health on all the metal and wood parts.
Yes that is quite unusual, since the LeMat is
such a rare piece, and you saw more than 4 at one exhibit. The most I saw once was two of them, a cavalry and a navy model. They just don't have the tendency to show up at gun shows that common.
such a rare piece, and you saw more than 4 at one exhibit. The most I saw once was two of them, a cavalry and a navy model. They just don't have the tendency to show up at gun shows that common.
J.T. Gerrity
Member
Also appeared in "12 Monkeys" with Bruce willis (strange in this sci-fi flick, but I'm guessing they just wanted a really big gun for his character to carry).
- Status