Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Went to Buy Colts and came home with a Cannon

Discussion in 'Blackpowder' started by WALKERs210, Apr 10, 2011.

Thread Status:
Not open for further replies.
  1. WALKERs210

    WALKERs210 Member

    Joined:
    Nov 26, 2009
    Messages:
    1,342
    Location:
    Heart of Dixie - Alabama
    Picked up this thing today and don't have a clue. It is brass and very heavy. Overall length is 12 1/4 inch with 1 1/8 inch bore. For lack of knowing the proper term I will call the back the breech/primer holding thing a majig. It has been semi drilled but does not penetrate into the bore. I have a breech plug from an inline rifle that is 1/2 inch in diam and from measuring the thing a majig it is 1 in in diam so it should be more than solid to mount. I was thinking that it might be easier to just drill a touch hole on top of barrel with a slight counter sink to hold powder. In other words I don't have a clue as to how to start or where to begin. I have "NO INTENTIONS" of ever live firing the canon but would like to at least fire confetti or just make fire and smoke.
     
    Last edited: Mar 30, 2013
  2. ojibweindian

    ojibweindian Member

    Joined:
    Dec 27, 2002
    Messages:
    2,300
    Location:
    Union Grove, Alabama
    I don't have a clue, either, but just wanted to say too cool!
     
  3. robhof

    robhof Member

    Joined:
    Oct 18, 2009
    Messages:
    1,003
    Location:
    Bowling Green Ky.
    robhof

    As a long time owner of small cannons, I would be very wary of firing that cannon as the barrel seems a bit thin. There's a certain minimum thickness to safely fire b/p as they are potential grenades with fatal results. Go onto the cannon and mortar area and read back about fatal accidents with real cannons and even the smaller ones. If it has a chamber of reduced size for the powder as do many mortars to use less powder and reduce blast pressure to the rest of the barrel, then it may be safe, but without a proof it's trial and error, and dangerous.
     
  4. WALKERs210

    WALKERs210 Member

    Joined:
    Nov 26, 2009
    Messages:
    1,342
    Location:
    Heart of Dixie - Alabama
    This is exactly why I ask.... Was told a long time ago that you can meet "Old people" you can meet "Foolish People" but its rare that you find an "Old Foolish" person. This was just way too cool to leave sitting there.
     
  5. rondog

    rondog Member

    Joined:
    Jun 29, 2007
    Messages:
    6,812
    Location:
    Commurado
    Looks to me like the barrel isn't even mounted to the carriage, it's just sitting there isn't it? I wouldn't fire it on a bet. Strictly ornamental IMO, probably homemade by some machinist.
     
  6. Berkley

    Berkley Member

    Joined:
    Nov 14, 2010
    Messages:
    365
    Location:
    Austin, Texas
    The "breech/primer holding thing a majig" is the cascabel, originally a place to attach arresting ropes to deal with the recoil of firing a cannon; on a small cannon it is just a traditional decoration. It should not be drilled through in a straight line with the bore.:eek: The touch hole should be at a right angle to the bore, on top of the barrel. The fact that it has not been drilled is a strong indication that the piece was never intended to be fired. I agree that the walls appear too thin for the size of the bore. As is, it is decorative. If fired, it would likely be a pipe bomb.
     
  7. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,743
    It is a decoration. The cascabel is not finished and there are no trunnion caps. If it were fired, the barrel would jump right out of the carriage, which is far too light and out of proportion.

    It is a pure dummy, and not even a good model of any real cannon. Without any knowledge of the metal used, it would be very foolish to try to make it into a firing gun. Stick it on the book shelf and look at it.

    Jim
     
  8. ClemBert

    ClemBert Member

    Joined:
    Apr 12, 2009
    Messages:
    1,168
    Location:
    Orlando
    Where is the cannon and mortar area? Link please for the blind. ;)
     
  9. Berkley

    Berkley Member

    Joined:
    Nov 14, 2010
    Messages:
    365
    Location:
    Austin, Texas
    If there is a cannon section in this forum I've missed it too.:uhoh: Try here or here.
     
  10. Busyhands94

    Busyhands94 Member

    Joined:
    Feb 11, 2011
    Messages:
    2,371
    Location:
    California, the "you can't have it" State.
    very cool cannon!
     
  11. ElvinWarrior

    ElvinWarrior Member

    Joined:
    Mar 24, 2011
    Messages:
    266
    Location:
    Los Angeles, CA
    I would fire it with 5Gr of BP blowing out a small handfull of confetti !!! That could be a fun toy to scare all the birds out of my fruit trees !!!

    Sincerely,

    ElvinWarrior... aka... David, "EW"
     
  12. arcticap

    arcticap Member

    Joined:
    Mar 20, 2005
    Messages:
    6,185
    Location:
    Central Connecticut
    If I really wanted to fire blanks with it then I would find a way to turn it into a noisemaker. I'm not sure what modifications would be needed to do that but where there's a will there's a way. :)
     
    Last edited: Apr 12, 2011
  13. 72coupe

    72coupe Member

    Joined:
    Jun 24, 2008
    Messages:
    914
    Location:
    Iowa Park, Texas
    Please be careful what ever you do. An aquaintence of mine built a small cannon and fired it for the first and last time on a July 4th. It killed him. Fortunately he made his kids stand back but they were there to see thier father die.
     
  14. Busyhands94

    Busyhands94 Member

    Joined:
    Feb 11, 2011
    Messages:
    2,371
    Location:
    California, the "you can't have it" State.
  15. 4v50 Gary

    4v50 Gary Moderator Staff Member

    Joined:
    Dec 19, 2002
    Messages:
    18,930
    Good score.
     
  16. 4v50 Gary

    4v50 Gary Moderator Staff Member

    Joined:
    Dec 19, 2002
    Messages:
    18,930
    Since cannons were mentioned

    Here's one for sale in Arlington, Virginia. Only $4k.

    [​IMG]

    link
     
Thread Status:
Not open for further replies.

Share This Page