Search results for query: *

@Smokey Joe- i dont have the funds to pick up a tumbler right now. I have every intention of getting one when funds allow. For the time being i have a limited budget to get my reloading gear.

Tried searching and couldn't find anything. What ways can you clean brass without a tumbler?

i've actually debated taking my calipers with me and measuring the distance between the mounting holes for both the xs7 and winchester model 70 s/a. Both of the charts show the marlin and winchester using the same front and rear bases for 2 piece setups so if the spacing is the same then the 1...

idk when x7vh gonna be available for purchase

i'm actually interested in the new x7vh for a budget long range rig but not sure on whether or not i can get a sloped base for it

i tried searching and found nothing...so nobody makes a picattiny rail with extra elvation machined into the base for the new marlin x7's. After doing some research and cross referencing i discovered that the long action x7(xl7) uses the same scope bases as the winchester model 70. My...

proof that times are changing. i graduated in '08 from cheyenne east high school but also attended cheyenne central highschool. All throught junior high and high school our p.e. classes had a 2 week archery unit. My first high school had both an archery team and an air rifle team. My second high...

It is a yugo. I already shot off all the herter's ammo i had and i always check and clean the firing pin and channel because i know they are known for stickin and causing slamfires. I've never had an cycling issues before this though.

So had a bad experience with a box of herter's 7.62x39 today. Took the sks out with 2 boxes of herter's ammo. The first box shot pretty normal with the exception of 2 where the empty case went sideways and didnt fully eject. The second box however was anything but normal...2 of the cases split...

The long trigger and long reset isn't an issue in my mind. What i was hearing was that the triggers weren't functioning right. I'm a firm beliver a less then desireable trigger can be overcome through practice. As i said my primary concern is reliability.

So my lady wants to get a sig sauer p250 as a carry gun; mainly due to the fact that she likes how the gun feels and fits her hand. While i know fit/feel of any gun is very important, i believe reliability is the most important aspect and i've heard rumors floating around the gun shop that the...

if you would like a heavier barreled rifle with iron sights consider these two fom savage MarkII FVT MarkI FVT one is magazine fed and the other is a single shot or if you want something with a little more range 93 fv here's the link to savage's sight http://www.savagearms.com/firearms/models

savage...accurate and affordable..idk about where your at but around here you can purchase a heavy barreled markII with a factory mounted and boresighted scope for under 300 otd which given the 4-500 dollar budget posted by the OP that leaves 1-200 for fair amount of ammo, a sling and possibly a...

bolt action 7.62x39..there are a couple on the market(cz527 carbine, ruger m77 hawkeye compact, and fn spr usa)...federal and winchester both put out factory loads intended for deer hunting and if u handload there are somr good bullets available for it..and pretty light recoil..

gamo makes a nice setup for 150 with the scope...most spring piston air rifles whether break barrel or wit a fixed barrel and a charging lever will run anywhere from 110-600 for ones not built specifically for competition...i have a gamo big cat and i love it, works great for targets and the...

egw and badger both make picatinny rails for the stevens( i believe its the same mounts as the savage 110 but not possitive)

buy him a hard take down case to go with it wrap the whole works...

1861 springfield musket...can shoot single roundball for large game or bein a smoothbore can shoot shot for small game and birds

around here anytime you get pulled over you're asked to get out of the vehicle...or at least everytime i've been pulled over i've been asked to get out of the vehicle...as have all the people i hang out with

b-square makes a mount for the 03a3 that requires basically no gunsmithingit replaces the factory magazine cutoff which i would think is easily switched back out and returned to original military condition...heres the link http://secure.armorholdings.com/b-square/springfield.html