Search results for query: *

  • Users: otiac
  • Order by date
  1. O

    ghost/halo sight for TC Hawken .50 cal

    Is there such that will fit an octagon barrel?. 50/.45
  2. O

    hipoint hicap mags

    Is there any current news on the hipoint mags? Is there any current info on HP hicap mags? Have the promags been improved at all for HP? otiac
  3. O

    Suggestions for DIY gelatinless handgun bullet test media.

    retired USNchief: the box of truth was very well done and interesting:about water "hardness:, on the Military Channel it showed why many troops in the water were not harmed, It was amazing to see how quickly the bullets lost all their oomf within just perhaps two feet after striking the water...
  4. O

    higher capacity for HP 995

    995 thanx double T, you would think in this day of technology, the answer would not be that difficult after all its only been forty three years sice Neil A did his thing. otiac
  5. O

    higher capacity for HP 995

    995 Thanx, a while ago there was mention by a member who would adapt an aftermarket for the 995 but I have lost the pertinent info.
  6. O

    Opinions wanted: Gunsafe type and placing on floor joists.

    heavy safe All the responses have legitimacy;remember, it is going to be a lot easier to do it nowbefore the walls crack, the floor dips and the joists bow. In addition you might consider throwing some "headers"/cross beams under the safe's position to strenghthen the joists.Pressure tereated...
  7. O

    higher capacity for HP 995

    Has anyone found a method to modifyaftermarket mags for use in the HPs? otiac
  8. O

    loads .260 Rem 24" bbl

    What are your best powder & bullet combos?
  9. O

    What to buy question. Vanguard, A Bolt, M77???

    OTIAC Howa Best info I get states Howa makes guts for their own, wetherby vanguard, possibly mossberg 4x4and Savage. Coug:new vanguard S2 has MOA and adjustable trigger which according to the mag writers is 2 1/2 -3 # set by factory.BTW Remingtons are not made completely in USA, factually, some...
  10. O

    scope again

    What thr opinions best 4x32 for $75-100? otiac
  11. O

    SR40 3 slot holster

    need advice on the subject;intention is for crossdraw thanx, otiac
  12. O

    .41 colt vs .41 special

    Mmcsret Thanx brother;one thing that confused me was the dia where as you said the coltis .386 while some are saying use .41 mag heads which run around .411. I believe John Taffin mentioned it is relatively easy to create .41 special brass by case trimming .41 mag. You have been a great...
  13. O

    .41 colt vs .41 special

    are these cartridges interchangeable in the same revolver.I'm having no luck finding dimensions for comparison;any reload data sources would be appreciated;enjoying the forums.otiac
  14. O

    Best Value Hunting Rifle

    New rifle? Look diligently at Gun Broker;I recently got a Rem 742 in 30-06 for lots less than other offerings and it has only a few ding in the wood.Using a 30-06 gives you a plethera of bullet weights so you can hunt anything from squirrels to Moose (110-220),otiac LOL Handloading and a good...
  15. O

    Gun Vice and Rest/Bags you like?

    gun vise GOOGLE gun vise and get the one for around thirty bucks,name esapes me but NSS has them,maybe even AMAZON.otiac
  16. O

    AK-47 7.62x39

    Any expert advice willbe welcome for me, a newbie,74 yrs old. thanx.otiac
  17. O

    where can i find grips for my 1911?

    NC Ordnance,ALTAMONT,Buffalo Bros.otiac
  18. O

    Grease: Jar vs. syringe?

    Might consider one of those frosting syringes for the grease;it will take care of large surfaces and on the advice of your other responders, q tips,artist brushes(usually can get at some dollar store for peanuts) toothpicks,burned wooden matches and so forth. LOL otiac.Barry
  19. O

    British web holster - correct wear?

    RU the Augustus McRae of Lonesome Dove TX? OTIAC
  20. O

    Securing a safe in a basement with cement floors - SOLUTION

    Or, get some angle iron longer than the width of the door, and secure it through the holes already there. You can use duct tape or epoxy to hold the bar in position for securing the bolts. Using some good line or steel cable, jury rig it so you can pull the bar up by going over the top with...
Back
Top