Search results for query: *

Course- Fundamental Handgun Date- 6/22/13 Taken at CCC Security Range Cresson Texas Given by Stephen Pineau with M3 Strategies This was the first training that I have taken other than what I have picked up on my own.* Was not sure what I was in for, but wanted to take my shooting up a...

I am trying to find a load for plinking.....I tried 5.6 gains of w-231 with a platted bullet from Xtreme 200 gain RN. Still getting powder blast in my face I did put a little tighter crimp on them (thinking it might help with the blast). But I am also getting some that keyhole at 10yrds. My...

I have been shooting the X-treme plated bullets and having very good luck out of them.....But every time I go to buy more I find myself looking and thinking about trying to switch to shooting lead, like maybe mastercraft bullets or something like that. The last time I tried lead it seemed...

I am looking for a gift for some one and I do not know much about over unders. I have been looking at the Browning citori line as well as the Beretta silver pigeon. Any help would be great.

I am thinking about getting a nice o/u but know very little about them. Please help looking for a nice gun to give as a really nice gift. I would like some thing in a 12 or 20ga

I am trying to FL size 308 case I am using RCBS sb x die but I keep denting the shoulders.......I have pulled the die apart and cleaned it still same problem. Lubing the case with RCBS case lube, cases have been trimmed to work with the x die. Press is a Lee classic turret used as single stage...

Ok I have been banging my head against the wall on this one. I have a DPMS LR 308 that I reload for but I get a lot of cases that will not chamber after I reload them. I am using small base dies from RCBS. The ones that do not chamber get stuck in the chamber. Not sure were my problem lies open...

I have tried titegroup as well as w231. The loads shoot fine but I sometimes get blasted with unburnt powder while shooting. My loads are midrange loads that seem to do well on the target but I might get a few per 100 that blast me. Sometimes every thing goes great then other I get...

I have been using corn cob media in a vibrating tumbler......Overnite give me a great shine and does a good job on pistol brass.....But I have noticed on my 300 wsm brass it leaves the neck with black stuff on the neck. Any way to fix this other than what I have been doing (by hand with a...

I load for 380, 9mm, 40, 45acp. I have been using titegroup but thinking there might be a better powder out there for me. The titegroup in my 45 seems to blow back unburnt powder that I am not happy with. 9mm and 45 it leaves a big burnt mark on the cases. Looking for opinions.

I have been reloading for a .308 AR it seems to have a lot of powder blast from the muzzel....It has quite a bit about double that of factory loads. I am using 41.5 grns of Tac which sould be about mid range..This is what gave me the tightest group. Any ideas (am I just using the wrong...

repost

I have just started to reload for my .308 DPMS....Now my question is this at 50 yrd same hole but at 100yrd i get about 5" group....Am I wanting to much out of this gun??:confused: My load is 41.5 gr tac with a 170 gr pulled bullet. My first thought was the bullet but most every one seems to...

I am trying to load for a AR308, I have the lee FL dies. but I can not get my round to chamber they get stuck......It seems like they did not get sized right am I doing something wrong? My set up is a lee press with rcbs lube die and lee FL sizing die. Any thoughts would be helpful...

Is is possible to have one can that could go from pistol to .223,300 blk? I have 9mm, 40 cal, 45 cal, .223 and soon to have a 300Blk is there one can that would work for all? with the cans and stamp being so much not sure how many I would be able to do, so I would like to find one to fit...