Search results for query: *

Thanks for all the tips on the mags guys. I bougfht the 20 rd P-MAG, with the 5 rd limiters. They install easy and I can grab ahold of the mag to get it out. Ready to go coyote hunting now! Take care Terry

Thanks for the headsup! I should have checked Midway! Do I need the 5 rd mag, or can I get by with a 10 rd holding 5 rds. For the IL boys that live in this SOCIALISTIC STATE! Thanks Terry

I'm in IL. Believe I need a 5 rd mag to hunt coyotes. Do they make them? I don't think you can use a 10 rd and just load 5. Thanks for your tips here. [email protected]

Thanks for your help guys! The gun was givin to me yrs ago, and just been sitting in the safe. I finally got some 25 ammo and decided to play with it. I was very shocked, at 20' the pistol grouped a golfball group! I figured it would give me a 10" group. I have plenty of good pistols, just...

Wolf doesn't sell any. Or can I just stretch the spring a little? The slide doesn't close 1/4" or so on a new round. Real easy to push it into battery. Thanks for your help! TerryR

Thanks for the info. Contacted Gunsmith and I'm sending her off. Thought I could do it. Take care Terry

Hi guys any help would be appreciated. Got a Wilson Ambidextrous safety for my Kimber Gold match. It fits in but won't go down to relaese the safety. Also on the other side (right) is a pin that protudes out, the wilson doesn't have a slot. Has anyone installed one and had problems with the...

Thanks very much! I'm searching now. Terry

Hi Guys I posted on the gunsmithing forum. Hopefully a gunsmith with parts or any knowledge to gain a part would be helpfull. Numrich has the part in 38S&W with out the hole. This is the LIL arm that goes up on the cylinder to rotate it. It broke and I need a new one. Thanks Terry...

thank you! I looked up my part (numrich) and it shows the lever for the 38 S&W. Would it be the same for my 32 S&W. Otherwise they don't show the part for my pistol. Thnaks again for any input. TerryR

Need Iver Johnson 32 S&W New Model topbreak Schematic and parts help. HI guys, I have a new model I J topbreak 32 S&W (short). It broke the LIL Hand that goes up on the face to rotate the cylinder. Anyone have a hand to sell and a schematic to show me how it all goes back together. I have an...

PM sent THANK YOU! Terry

Private message (PM) sent to you Jim on the White Powder Wonder 20 ga shotgun. Thanks Terry

PM sent to you Jim, Thanks Terry

Found a 20 ga "White Powder Wonder" 20 ga shotgun in a rental house. Anyone know where I can get a front forearm stock for it? Its possibly a stevens, or 5 other makers from what Ive found out so far. Made for Sears. Any help would be appreciated! thanks TerryR

Hi guys, I took apart my Marbles rear sight to fix it and putting it back together is not working. It has a spring inside that lifts the sight forward and holds it in place. Anyone know how to put the spring back so it has tension on the sight? Or, any help on another website would be helpfull...

I tried Rodacy Bluing then tried Brownells Parkerizing, was going to go buy BW Caseys perma blue next. But don't think that'll work. I stuck a magnet on it and it sticks. I thought it was stainless also. But I do know that 309 stainless will take a magnet so I was just trying to figure this out...

Thanks guys I got the safety apart and OFF. Then I cleaned paint off, acetoned clean. Then tried to blue. It won't take the bluing! It just stays silver. It has a 2 with a cirle around the 2. Is that some kind of metal? Thanks TerryR

Hi guys My Navy son came home with his Kimber gold match pistol. It has the ambidexdrious safety. The black paint on the right side is worn off the safety, Don't know why it was painted. Bought it brand new on gunbroker 2 yrs ago. Question #1: Can I reblue it? It has black paint on it...