Search results for query: *

hello, i have two vintage light weights a 1966 vintage cobra and a S&W model 12 no numbers, I would like to buy a box or two or carry ammo, plus p is out of the question, , any recommendations, I have been carrying either federal 125 gr HP nyclads or , western 200 gr rn please post, many thanks,

hi , i am looking to buy and then reload .455 British service load in either a new service or a S&W hand ejector , looking for a bullet mold to buy. either a 4 or 2 cavity mold, please post, many thanks

hi all, its new years eve and wondering if anyone still make a .44 auto magnums / I know I most likely can not afford one but curious, please post robbt Athbhliain faoi mhaise daoibh

hi , can someone explain how the fees work on gunbroker ?? I am looking to buy I was told they went up ? please explain, many thanks

hi guys , I was referred to Steves pages, I found a post here concerning Steves Pages have they been move or closed , please post , many thanks, robbt

hello all , I recently found a box of .357 magnums I loaded some time ago with 12.5 grs of 2400 using Lyman 357446 , I plan on shooting this load in a model 19 and a couple of other medium non n frame .357 revolvers is load too hot ?? please post, many thanks

hi guys , has anyone had any luck removing rust from a nickeled sixgun ?? I acquired a S&W with a couple of rust spots, not spec, stops please post, many thanks, robbt

hi guys , i would love .30 cal. FMJ 180 gr. similar to one picture below, sorry for bad picture, this is the last from batch of .30 caliber Western 180 gr Palma match ammo, ammo was stored in a shed and got wet , brass was pitted so I pulled the heads. would like to buy bulk only cannot afford...

howdy boys , i am seeking a source for .30 caliber FMJ in 150 and 180 grains for shooting in my M1 and 1903 springfields cannot afford sierra , and ideas, would like to buy in bulk please post, many thanks, robbtq

hi guys , anyone get a Stimulus Checks yet ??? please post

hi guys , I find my self lacking in factory .45 acp. I have a lot of 210 gr truncated cone round nose lead bullets , I also have a lot of accurate #2 powder , can someone assist me in a combat load for defense?? please post , many thanks, robbt

hi , I am in the market to my a .455 revolver, would prefer a colt , but a clean Webley or S&W will do. whats a good bullet to use in these old war horses , is the a old mold I should look for casting. also brass too , who make any ?? please post,

hi , I have a batch of .357 sig brass, whats it worth ?? please post, robbt

howdy , always interested in new reading material what are you favorite gun books ??? please post

hello, a picture below is a 1959 S&W model 12 Airweight , basically a S&W Aircrewman with a steel cylinder, I am inquiring on what loads I can use in the old girl without harming the revolver , lets discount +P. seeking a carry load in the rare time I will carry concealed . any ideas does...

hi , I recently purchase two S&W . 41 magnums , and a several hundred pieces of brass , wondering how much 2400 to use with 200 gr lead bullets . it doesn't hurt to ask, m

Hi guys , I require your advice, I am planning on doing bulk reloading for my 1930- 1948 S&W k frame using the Lyman 357446 Thompson SWC bullet with the AOL of 1.457 utilizing the lower crimping groove. The revolvers are of following a 1932 M&P, a early post war commercial victory, a WW2...

hi , hopefully someone here can assist my , I have started reloading 358429. Lyman/ Keith swc bullet for my 3 colt .357 [ pre trooper style revolvers ] , I would to generate approx 1100 fps , but I am afraid of using too much 2400 powder. general published load on this bullet use the n frame S&W...

hi guys , I acquired a 1939 Mauser Built Luger , just wondering if anyone handloads soft or hollow points for there Luger and can post some advise ?? many thanks, robbts

good evening , I am seeking to buy a brown luger military style shoulder for my 1939 vintage mauser p08 luger . I am looking for something similar to the one picture below , any idesa ??please post, many thanks, robbt