Search results for query: *

This is an updated to the 2018 Miami Beach case where an open carry advocacy group was detained for 80 minutes after they open carried on the Miami Beach Pier. They argued their detention was a violation of their rights due to the Florida exception which allows open carry while engaged in...

So I had the slide off my brand new G17 Gen 5 when I fumbled it over our tile floor...appears to have landed on the back corner slide rail which bent the rail and now two visible cracks are present. This is the second time I've seen this happen to a glock slide that was dropped. Glock wants...

Just picked up an LE6920 and upon inspection noted this towards rear of upper receiver. I don't care if it's simply a scratch but since it originates from a corner, I figured I'd ask. It's easier to see in real life than this picture.

I recently bought a glock 26 gen 4 for a backup and had 3 stovepipes/ftf in our 40 rd qualification. Ammo was fiocchi 115gr fmj. Took I ran another 150 rds of 115gr blazer fmj and another 50 rd box of fiocchi. With the Blazer I had to try REALLY hard to induce a stovepipe by lightly...

Got the itch for a full size DA .22 mag. Any thoughts on the Taurus Tracker models?

Looking at the 4.5" slide safety models I notice Dark Earth says 6.5lbs and others mostly say 7lbs. What's different?

I weighed my LTR today. 10.4lbs without the BiPod or Ammo. Yikes. I feel like this defeats the point of a handy 20" bolt gun. Current setup: LTR ~7.5 LBs Williams Bottom Metal (steel) Badger Base and rings (steel) SWFA 3-9X42 By swapping for Badger Alloy Rings and Base and...

Hey guys need a favor. I replaced the bottom metal on my LTR with a Williams piece. Dropped right in..except..the internal box that fits between the bottom metal and the reciever is a skosh loose. If you pop the latch and feel it, you can move it up and down a wee. Would any of you kind...

Considering one for CCW during summer..but the slide cracking is a little alarming. Have they resolved this yet?

Just in case anyone wants to email this guy... http://www.sun-sentinel.com/news/opinion/todaysbuzz/thursday/sfl-should-florida-join-the-states-proposing-concealed-weapons-without-permits-20120307,0,3013435.story

Been reading some good things about them, might offload my G21 for one this week. Have they got the issues sorted out with the SF model yet?

So when putting my G21SF back together I inadvertently installed the slide onto the frame above the rear slide rails. I'm actually pretty surprised it would go back together this way, but I suspect the front rails are higher than the rears. In order to remove the jammed slide I had to run...

Hey guys..sorry if a dumb question. Two different M&P 40s at the gun store..one has a plug blocking the internal lock where the key would go..the other has no such plug but has the square plugs blocking holes where the thumb safety would go..why the variation..what am I missing? Pretty sure...

Just recently acquired a 6.5" stainless Single Six in 17HMR and noticed gap appeared a bit wide so I decided to measure it. Cylinder to the rear, hammer down .009, .010 No go Cylinder forward, Hammer down .008, .009 No go This seems to be on the high side, thoughts? For comparison, my GF's...

I'm thinking about picking one of these up for carry...any durability differences between the two cartridges?

So I'd like to purchase a really good safe when I get back to the states. I'm not much into rifles..but I'd like something pretty hardcore for protecting my computer..documents and of course handguns and watches when I go on vacation or TDY. I like the GSA type heavy duty safes I see that we use...

So if I'm wanting to legally make some FTF sales in my state, is there any magic number of transactions that makes an FFL required? I'm probably going to be looking at offloading 5-6 guns.

So I know a lot of the people who own the Colts and other high end AR15s appreciate the slightly better 4150 steel they use because they claim it is stronger. I wonder if it HAS to be stronger since it goes pencil thin at the M203 attach point on a govt profile and is also pretty thin under...

I know the 16" guns are more popular and for those the Colt has some nice features, better barrel steel and some other things that have been beat to death. I have been saying over here though that if Colt sold a flattop 20" like the M16A4 I'd love to snag one. low and behold they have been...

Short of charging bears, if care is taken for proper shot placement, is there really anything one couldn't hunt ethically with a .243 in the lower 48?