Search results for query: *

I've got one. What information do you have? [email protected] Thanks, Brian

"While you're at it why not have your smith trim that lug off ? That would be sweet if you could get it down close to the weight of a model 19 with 10mm power." A 66 is 37 oz, my 686+ Mountian Gun is 37.5 oz with full sized houges on it. My 646 non PC & thus full lug is 35 oz. Long load...

I've taken 3 or 4 big whitetails w/ a G20 No problem. I took two in one afternoon. I prefer to keep the shots under 35 yards, but the gun is plenty accurate beyond 50 yds. All shots except one was T&T broadside. The one that didn't make it out was in the far shoulder of a very large deer 40...

Dear Good & Kind Sirs/Mames: I would like to hear from those of you who have taught enough youths (read Boy Scouts) to shoot shotgun that you can draw on personal experiance to tell me if a rib on a barrel is a notable advantage to learning the art. I am endervering to guide shotgun (&...

Benelli, Browning and Remington.. But the one that stumps me is a Stoeger tube mark. X

I need to make sure I have the markings down for some choke tubes I have- is: 1= Full 2=IM 3= Mod 4=IC 5= Cylinder? What is skeet I & II marked? This also goes for marks on a barrel (ie an old A-5 w/ 1 star=Full) don't it? TIA! X

This works for me: Jandd FFP: fits on front of frame "below the top tube and behind the head tube. " Bowser Banaca & a poodle shooter (Guardian Pepper Spray & A Kel-tek) ride in mine- quick to access while mounted, easy to take off if leaving the bike...

4"- Sweet! That makes it IDPA leagal! X

Yup. Here you go- (re-post) USE AT OWN RISK 1st- this is a revolver load only. 2nd- Unfluted cylinders are stronger than fluted because they are butt-ugly- ugley is strong- just look at Ruger revolvers.) I have touched off tons of these in my fluted 610. Presure signs are far less than a...

"I'd be satisfied with 55 miles per gallon out of my Chrysler, no question. From your mouth to G*d's ear.

10mm SUCKS! Oh wait a minute, - Nevermind. Seriously, I have a 5" 610 reamed to 10mm Mag. I can shoot a 135 .40 S&W load at 1100 fps, in an N frame it kicks like a .38 in a 686. My 10mm Mag loads (Beartooth 200 gr w/ canalure or 220 LFP) are clean into the .41 Rem Mag's lunch. I've shot 8...

10mm TPH Just kidding. Ti 610+ Mountain Gun. w/ Second steel 6 shot cylinder (fluted) and hand for IDPA.

Them fellers pointing at Colts are right. All other .380s (even the Glock) are blowback AFAIK. This makes them kick out of proportion. My single stack Beretta feels like it kicks a lot more than my P9 Kahr (both shooting defense loads from CorBon.) It also means they have very heavy recoil...

I did a comparison in 2002- Hk 93 back when they went for $675 w/folding stock VS. the median large cap mutual fund. $675 in the stock fund after taxes and fees would have bought 6 or 7 $3500 93s in 2002. You may get lucky, but it’s really just a way to rationalize gun purchases. Don't...

Ya ain’t a Navy SEAL until you taste Italian steel.

Don't that change a handgun into a handsgun? If I have to use two hands to run it, I'm opting for something biggern' a pistol! Defeats the whole concept in my mind. Besides, just like in all them moving picture shows - Them fellers always have to have the off hand free to hold a damsel...

Marlin 25MN Mag 6 rounds, dirt cheap. Flip out with a push of your thumb. I've found them used at shows for $5.

Herters option If you have a loading press, 41mag shell plate, Dillion 10mm sizing die & case trimming tool you can make .401 PowerMag rounds from .41 Rem Mag brass. This works quite well. 1. Trim brass to .401 PM length (measure factory case.) 2. Warm brass (I put it in an oven @ 170 for...

Gordon said "1927 &1928 Machineguns" Didn't John Thompson design the Tommy Gun?

THRers, My son asked me what guns JM Browning designed. I started to list them, then told him I’d have to get back to him. If you’re 100% sure of your answer (and preferably cite references) please feel free to comment (I am befuddled by the list thus far as it is.) Thus far I have...