Guys I need some help. A buddy of mine has a .300 win mag that accuracy has went south on upon inspecting the rifle it has bad copper fouling. What product or home brewed concoction is best for removing copper fouling
I'm asking this question for a friend who is wanting to lighten the trigger pull on his Super Blackhawk. 44mag. He had heard something about removing the grips and unhooking a spring to lighten the trigger pull. I was some what skeptical of this and told him I would ask you guys about this. Any...
Hey guys just a question is there way to tighten up the cylinder on a blackhawk? Upon lock up my pistol has a small amount of play in it. Any info appreciated.
Guys have any of you had any experience with the eaa witness elite match or the hunter model in 10mm.My dad is looking at getting one for hunting and was curious about accuracy out to 100yds. any info or opinions greatly appreciated
Guys I was displaced from my home for about a year because of a natural disaster my reloading equipment was in storage for around a year now that I am settled in to my new home I was setting up my loading bench and alot of my stuff has rust namely my dies that I am worried about is there any way...
Guys I got a new toy. A savage model 10 in .243 win. the twist rate is 1 in 9.25 and seeing as i didn't have any brass I went down to my local wally world and purchased a couple of boxes off the shelf so I could "make brass" any way I know the rifle dose not like the 100gr factory loads I was...
Guys I need some info a friend of mine has a montgomery ward super drednaught single shot 12ga. Well he dropped it the other day and busted the buttstock. Any ideas where we can find a replacement stock? It is kind of a family heirloom and holds sentimental value and they would like to have it...
I have shot both loose powder and pellets before. I went to pellets awhile back but now since i reload and realize that 5 grains of powder up or down can open or close groups in centerfire rifles i was thinking the same may hold true for blackpowder. give me some of your opinions
Worked up some new loads for my stevens model 200 in .308 today and went to the range and wow!!! My 100yd group measured .71 inches for 4 shots and my 200yd group measured around 1 and a half inches for 3 shots.I cant wait to see what this rifle will do after i get a rifle basix trigger and a...
Guys I want a "new" milsurp as in new to me. I was thinking of a K98 if I can find one under 200.00. My local range has a milsurp rifle shoot every month and the ammo for my m95 steyer is getting scarce. I also thought of a mosin-nagant or a schmidt ruben but just wanted your opinions on the...
Guys I have been wanting to either buy or build a 6.5 caliber rifle and am torn between the 6.5x55 and the 260 rem. I will handload for wich ever one I decide apon. Does one have a ballistic advantage over the other. And is the 6.5x55 brass readily available?The rifle will primarily be a range...
:banghead: Guys I have just purchased a marlin model 81-dl and I have feed problems. It appears I may need a new cartridge carrier and extractor (I believe my nomenclature is correct) any way the carrier lets the cartridge flip up insted of holding it in line with the chamber if I push the...
cz52 extractor
what is the proper way to remove the extractor pin? do you drive it from the top to the bottom or do you drive it from the bottom to the top? or does it matter? i have changed out most of the slide components and need to do a little work on the extractor. any help would be...
what is the proper way to remove the extractor pin? do you drive it from the top to the bottom or do you drive it from the bottom to the top? or does it matter? i have changed out most of the slide components and need to do a little work on the extractor. any help would be appreciated, thanks.
Guys I picked up a Marlin 81-DL at a pawn shop today for 65.00 It is haveing some feed problems I was wondering where I could get parts for this rifle? From what I have read it appers to be pre WWII production
Guys what is the cleanest burning powder for .45acp with cast bullets? I Have used clays ,Tightgroup and unique they all seem to burn rather dirty with tightgroup being the cleanest.Is there another powder suitable for .45acp that is cleaner.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.