Search results for query: *

I picked up some 200gr cast SWC and 230 cast RN am going to load some up tomorrow. Thinking about starting at 4.0 of Bullseye and working up from there. Any favorite loads using Bullseye from you guys?

I have never loaded anything except jacketed or plated bullets. But times being what they are I thought I might need to try something else. Anyone have any experience with S&S bullets? Good - OK -Oh No. :) Thanks

I picked up some of these today because that was all I could find on the shelf, I was not wearing my glasses ans discovered they say as used in our revolution lever action ammo. I cannot find any load data on them, and they were to be loaded for a AR-10 vrs a lever action. Anyone know...

I have a Armalite AR-10, an Armalite scope mount with a Nightforce 2.5x10-24 on it. I like the set up very much, but, it sits a little low. I really do not want to get a whole new mount but I need to raise it up just a tad. Who makes or what kind of risor would you use? Thanks

.45 ACP, anyone load these? I have loaded up to 5.2 grains Bullseye, but do not have a crony and was thinking on making some a little hotter, but I am not sure what the max would be. Thanks

My son shot in his first practice match this week and did well, using some make shift equipment, he is a south paw and wants to shoot in the future. Getting left handed stuff is almost a special order but I found a holster in stock. He is shooting a Baer 1911 in 9mm, either single stack or...

Which would you get? I do like the extra weight of the 232 but I like the trigger of the 238. I have not fired either though and I am looking to replace my LCP, snappy little bugger. :eek:

I am going to be getting a new Ruger Blackhawk for plinking and was wondering what caliber you would get and why. I have had 44MAG's in the past and really enjoyed them, recently though, some have suggested 45LC. Thanks

Is there a difference in slide stop dimensions, between 45ACP and 9MM? EGW and Wilson have them listed separately but, other makers do not. I tried a slide stop out of one of my 45's in my 9 and it worked better than the original one that is installed. I am needing to replace the one in...

Was the 10-6 available in 357mag? Am I correct that it would have been made around 1962? I was thinking on trading for one but not sure what it would be worth. I just do not know much about them. Thanks for any replies.........

Any one tried them, I have not shot cast before and with prices now days I was thinking on giving them a shot. thanks Well after some searching I guess they are no more........

I have a FO sight on a Baer that I was thinking of changing to a Gold/Brass bead. I wondered if anyone had ever tried inserting a gold/brass rod the same size as the FO. In this case I believe it is .060. Just wondering because then one sight could work for both. I have both FO and bead's on...

Does 9mm Glock brass have this bulge? The reason I ask is using my Dillon 650 and some brass I know came out of a Glock (wife's). I still have no problems with gagging the finished rounds? Fit and shoot fine out of my 1911. :confused:

Small or Large, anyone ever used rifle primers for pistol loads? I have lots of rifle primers that need to go as I do not load for my rifle much anymore. Thanks

Shooting today and had the hammer follow (to half cocked) after around 1oo rds, never had a problem with this 1911 before. From slide lock, insert mag and hammer would follow (almost every time). It was hot, around 100 degrees today. Would the heat have any influence on the follow? The reason I...

45 ACP - 1911 5" barrel I have been using the following for awhile but wast wondering if any one had any load data or might have better loads, I have no way to measure the speed or check for the power factor shooting in USPSA. Accuracy seems pretty good but just wanted to check with you experts...

What do you guys use? Looking at Dillon's, not sure. Thanks

What are you using? I shoot 1911's and the finish on them is getting pretty scratched up using the cheap $20 plastic holsters. I am thinking about going back to leather maybe an Avenger type. But I do not feel they are as quick. Just looking for any recommendations. Thanks

Has anyone ever used Magnum or small rifle primers when loading 9mm? I have heard it has been done but I do not remember where/when. I have spoken to a few people who reload and they are ya not a problem. :scrutiny: Thing is I have a boatload of small rifle and some magnum that I want to use...

I know this has been ask before but, what is a good "lite" load in 45 ACP? My son is 12 and has tried my 1911 with 230 fmj and 6.0 grains of WSF. He really liked it.:D So being kinda new to reloading I was wondering what you guys would recommend for a good load for him. Thanks for any replies