Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Black Powder Revolver Manufactures

Discussion in 'Blackpowder' started by MrTuffPaws, Aug 5, 2013.

Thread Status:
Not open for further replies.
  1. MrTuffPaws

    MrTuffPaws Member

    Joined:
    Oct 7, 2004
    Messages:
    1,511
    Location:
    Az
    I've been considering getting into some black powder shooting with some revolvers. My eye has been settling on the 1858 Remington over and over again. An original piece is out of the question due to funding. A repo will be the way to go.

    The trouble being that I don't know much about the quality of the various manufactures. The ones that I can find that I have access to are Traditions, Uberti, and Pietta. Any one to avoid?
     
  2. Fingers McGee

    Fingers McGee Member

    Joined:
    Apr 5, 2009
    Messages:
    1,465
    Location:
    High and dry at Lake of the Ozarks, MO
    Any of them would be ok (traditions are made by Pietta). There is a little difference in grip profile between them, so you should at least handle them before purchase so the one you buy 'fits'.
     
  3. realitycheck

    realitycheck Member

    Joined:
    Jul 30, 2013
    Messages:
    45
    Location:
    all over.wherever i want to go.
    revolvers

    when i was in your position,i found the 1851 Confederate Navy by Pietta on Cabelas. It was the best priced and is solidly made. Very nice wood,tight cylinder,shiny brass/blue, and that was the least expensive model.
    I think the 1858 Remington would be a better way to go,theyre a little stronger with the topstrap i think.
    Whatever kind you get,
    MAKE SURE YOU GET ONE WITH A STEEL FRAME instead of a brass frame. They are stronger and last longer and can handle heavier loads. They will cost a little more though. check Cabelas.com.i think now theyre giving away starter kits with new revolvers. Use .454 balls in the Pietta models. in bp revolvers,wads are to prevent chainfires from sparks getting in from the front,not for ballistic reasons. Id rather put a little lube seal over the ball than buy wads.saves money.
     
  4. mykeal

    mykeal Member

    Joined:
    Sep 9, 2006
    Messages:
    5,147
    Location:
    Michigan
    Chainfires are caused by hot gasses, not sparks.

    And 'starter kits' are notoriously poor values.
     
  5. realitycheck

    realitycheck Member

    Joined:
    Jul 30, 2013
    Messages:
    45
    Location:
    all over.wherever i want to go.
    the starter kit comes with the revolvers at the same price as just a revolver used to be at Cabelas online. Whether or not thats a poor value is up to the person buying the revolver i would think. "Hey buddy,its 179 at Cabelas with a starter kit, so go buy it at Basspro for 179 without one,because theyre notoriously bad values!"

    And i beg to differ about the chainfires, there was a whole topic about it in a blackpowder forum being fire from the discharching cylinder/cap getting into another cylinder and causing it to fire. And accordingly,most chainfires happen at the nipple end. I guess as far as semantics goes,i should have said "fire" instead of "spark".

    funny
     
  6. Norton Commando

    Norton Commando Member

    Joined:
    Mar 4, 2011
    Messages:
    279
    Location:
    Houston, Texas
    Hi MrTuffPaws,

    The 1858 Remington is a great choice. I have had one since 1982 and it still performs perfectly. It's an Armi San Paolo, which has been out of business for quite a few years now. And as realitycheck pointed out, the steel frames are stronger than the brass ones.

    I think there are only three manufacturers of black powder revolvers: Uberti, Pietta and Armi San Marco. Quality control for all three manufacturers is spotty. But with a little effort, the QC/QA problems can be corrected. If it were me, I'd simply purchase the least expensive of the three in a steel frame. And who knows, you may get a perfect gun right out of the box, many people do. If you don’t, there’s plenty of help on this forum and others, so have no fear of getting a gun that’s a bit “off”.

    Good luck,

    Jason
     
    Last edited: Aug 5, 2013
  7. Acorn Mush

    Acorn Mush Member

    Joined:
    Dec 24, 2007
    Messages:
    444
    Location:
    Acorn Mush, CA (Better than living in Lard)
    deleted
     
  8. Pancho

    Pancho Member

    Joined:
    Oct 23, 2007
    Messages:
    1,874
    Location:
    Southwestern, Ohio out in the country about 40 mil
    So currently only Uberti and Pietta are making reproduction revolvers. Just wishing here but wouldn't it be nice if Ruger and,or Colt got back into production? While I'm wishing maybe they could not only make expensive quality repros but would also offer an affordable line comparable to the Italians.
    Dream on old man dream on.
     
  9. vagunmonkey

    vagunmonkey Member

    Joined:
    Apr 23, 2012
    Messages:
    173
    Location:
    Virginia
    If your looking for quality over price, I would consider a Pedersoli...

    Otherwise, I like Pietta and definitely steel over brass.
     
  10. Mike OTDP

    Mike OTDP Member

    Joined:
    Oct 31, 2007
    Messages:
    1,678
    Location:
    Somewhere in Maryland
    The repro revolver makers in order of desirability:

    Tier 1: Hege Army Match Maximum, Feinwerkbau History #2 (Rogers & Spencer), Baumkircher Remington

    Tier 2: Pedersoli, Pietta Shooter's Model

    Tier 3: Everything else.
     
  11. Pancho

    Pancho Member

    Joined:
    Oct 23, 2007
    Messages:
    1,874
    Location:
    Southwestern, Ohio out in the country about 40 mil
    Whew! I just checked the cost of a Pedersoli Remington repro. $880! ON SALE!
     
  12. vagunmonkey

    vagunmonkey Member

    Joined:
    Apr 23, 2012
    Messages:
    173
    Location:
    Virginia
    Yep...and the Pietta shooters model will be about $800 on sale. Both are worthy of consideration if you want a quality shooter.

    As previously mentioned, the Hege and Feinwerkbau are first choice, but at $1700+ are non starters for most of us :(
     
  13. mitchz

    mitchz Member

    Joined:
    Oct 16, 2011
    Messages:
    68
    If you can find a stianless in your price range buy it. They are the strongest and easyest to clean. Full steel are second chioce and brass frames are last.
     
  14. Crawdad1

    Crawdad1 Member

    Joined:
    Sep 13, 2012
    Messages:
    2,826
    Location:
    Pennsylvania
    I love my Signature Series Colt 1860 Army and its very accurate. Its the only one I shoot, I have two other Signature Series Colt's and a 2nd generation 'F' series 51 Navy that just sit in glass cases. For someone just getting into the black powder revolvers, I would get a Remington. They're a lot easier to get on POI and overall easier to deal with. The Colts are tricky and need a lot of patience and sometimes some good ole Kentucky windage, to shoot as good as the Remingtons.
    But regardless of what you buy, the feeling you get when you start zeroing a black powder revolver and start blasting stuff cannot be described.

    And some of these revolvers are sold on line at the auction sites, look there also for a good used one.

    Good luck to you whatever you buy.
     
  15. BowerR64

    BowerR64 Member

    Joined:
    Aug 1, 2013
    Messages:
    1,244
    Ive only been shooting my C&B about 2 weeks and i already like the Remington clones over the Colt.

    2 things that i like better, its easier to load with the cylinder in the gun then the colt and if you need to remove the cylinder its easier to get it out.

    The front frame on the colt is a bit fat on mine and i have a hard time loading it. Also the wedge needs a hammer to pound it out mine fits so tight.
     
  16. Crawdad1

    Crawdad1 Member

    Joined:
    Sep 13, 2012
    Messages:
    2,826
    Location:
    Pennsylvania
  17. EljaySL

    EljaySL Member

    Joined:
    Sep 10, 2011
    Messages:
    636
    Location:
    California
    I definitely think the Remington clones are easier to deal with. Some of my Colts have had problems with too soft mainsprings = soft strikes, plus one had a wedge that took tremendous effort to remove the first time.

    But once you get them running... the first time my 1860 really ran properly it shot a smaller group than my 1858 and it has ever since. I think it's a balance/pointability thing - it's just easier to shoot.

    So my advice is to enjoy the 1858 and know you got a great starter gun. But borrow a Colt sometime or just pick one up next time Cabelas has a great sale (day after Thanksgiving) and see for yourself. Just bring the 1858 to the range too in case the 1860 doesn't actually work so you'll have something to shoot...
     
  18. Skinny 1950

    Skinny 1950 Member

    Joined:
    Jul 2, 2010
    Messages:
    532
    Location:
    Vancouver B.C. Canada
    MrTuffPaws if you are drawn to a Remington 1858 You should go for it, I was drawn to a Colt 1851 so I bought a Uberti but now I have 1851's made by a lot of different makers along with 1849's, 1860's,an 1862 a few 1873's etc. etc..
    If it is your first BP revolver it may not be your last.
     
  19. MrTuffPaws

    MrTuffPaws Member

    Joined:
    Oct 7, 2004
    Messages:
    1,511
    Location:
    Az
    Thanks for all the input. Sounds like I can easily get buy with what I can find locally. Just waiting now to find a steel frame model. The only ones I have ran into here are brass framed. Just net to be pateint is all.
     
  20. Pancho

    Pancho Member

    Joined:
    Oct 23, 2007
    Messages:
    1,874
    Location:
    Southwestern, Ohio out in the country about 40 mil
    The steel frame guns cost more new and used for good reason.
     
  21. Crawdad1

    Crawdad1 Member

    Joined:
    Sep 13, 2012
    Messages:
    2,826
    Location:
    Pennsylvania
    Are you sure you can't buy on-line? Bunch of good stuff on auctionarms and gunbroker (don't like gunbroker but they always do have a bunch of revolvers for sale nearly 8 pages).
     
  22. whughett

    whughett Member

    Joined:
    Mar 26, 2008
    Messages:
    745
    Location:
    Rhode Island/Florida
    After yesterdays range session with my Ruger Old Army I am beginning to wonder why I put up with the the other repros. Ten full cylinder loads, 60 shots
    no hang ups no cylinder dragging just smooth hammer action, crisp trigger pull and a fully adjustable rear sight, just like the GP100.

    Having said that I still like the Walker and 1860 Colt. Guess these things are like women, all are nice just some are nicer.
     
Thread Status:
Not open for further replies.

Share This Page