CoalCrackerAl
Member
Most of the rounds would not eject. But the ones that did. Landed on the bench next to the rifle. Im going to bump up my loads by a 1/2 grain. And some up 1 grain. And test those.
I guess. But then again it's a rifle mod i did.
A gunsmith in know that used to work on them says every inch you cut off the barrel if you're lucky will shrink groups by an inch at 120yd. I'm pretty sure he was talking about factory ammo.Instead of changing my bushing, I cut 5.5" off the barrel! Gas system is now perfect
Mine shoots better for sure! 60 yards, Tech rear sightMost accurate mini14 load I know of uses around a start load of H322.
Probably wouldn't cycle.
The port drilled into the barrel should be about 0.05'' on my new barrel in drilled mine out to 0.062'' so I could run RE7 loads, which I still haven't tested yet.
A gunsmith in know that used to work on them says every inch you cut off the barrel if you're lucky will shrink groups by an inch at 120yd. I'm pretty sure he was talking about factory ammo.
Yeah, of course you have the short stock with folding butt, and a muzzle brake.
Where do you get those stocks ??
It's a factory folder, but as mentioned, they offer a aftermarket.Yeah, of course you have the short stock with folding butt, and a muzzle brake.
Where do you get those stocks ??
Yeah, that one ruined the group! lolI get 4moa cold shot fliers its going to have a boating accident.
It's a factory folder, but as mentioned, they offer a aftermarket.
The above mentioned 5.5" barrel reduction sounds about right then. Shrink groups by 5" to get MOA out of a couple I've had.every inch you cut off the barrel if you're lucky will shrink groups by an inch at 120
Depends on which you have. Mine had the Ruger rings, some put rails on. What kinda rings do you need? I had a small hollow mount that clamped on where the Ruger integrated rings would so you could use Weaver or picatinny type.Well thank you guys for the tips. But right now I do need someone to send me a link to buy scope rings for the Mini-14. Where and how do I find them ?
Yours didn't come with rings? Mine came with steel rings. They have a piece on them that wont let them walk too. I really like them. I have a Burris scope on mine.Well thank you guys for the tips. But right now I do need someone to send me a link to buy scope rings for the Mini-14. Where and how do I find them ?
I have a black poly stock for mine, and would like to see how it groups with it. The factory folder is not a good stock for tiny groups! The 18.5" whip that I cut down, was notably less accurate.The above mentioned 5.5" barrel reduction sounds about right then. Shrink groups by 5" to get MOA out of a couple I've had.
Depends on which you have. Mine had the Ruger rings, some put rails on. What kinda rings do you need?
Mine came with steel rings.
Wasn't much...$30 or so IIRC. If I can find it I'll send it to you. Wouldn't work on my Target model and I was having lots of trouble getting the right ring combination for a 42mm objective. Finally got the right rings on eBay. This is what the mount isHow much did the clamp converter cost though?
It's only real purpose is to allow use of open sights along with a scope. The tube is only like 3/8" diameter, so it has less field of view than a scope.I didn't need a clamp converter
Wasn't much...$30 or so IIRC. If I can find it I'll send it to you. Wouldn't work on my Target model and I was having lots of trouble getting the right ring combination for a 42mm objective. Finally got the right rings on eBay. This is what the mount is
https://www.ebay.com/itm/1258157323...HupKpHGTMC&var=&widget_ver=artemis&media=COPY
It's only real purpose is to allow use of open sights along with a scope. The tube is only like 3/8" diameter, so it has less field of view than a scope.