Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Headspace on a M1 Carbine if you change out bolt

Discussion in 'Gunsmithing and Repairs' started by ozmosis, Nov 11, 2010.

Thread Status:
Not open for further replies.
  1. ozmosis

    ozmosis Member

    Joined:
    Jun 8, 2007
    Messages:
    53
    Just a quick question,
    After a search of the forum I have not found a answer.
    On the M1 Carbine if you swap out bolts (like if you are trying to switch to a flat bolt) would this effect your head space? Any other issues I should be aware of?
    Thank you in advance.
     
  2. Lee Roder

    Lee Roder Member

    Joined:
    Jul 15, 2009
    Messages:
    510
    Location:
    AZ
    It may or may not. Bolts on all five of my carbines each headspace correctly with any other barrelled assy. Probably just lucky. You really must check it with a field gage yourself and assume nothing.

    HTH
     
  3. highorder

    highorder Member

    Joined:
    Oct 7, 2007
    Messages:
    4,349
    Location:
    Cincinnati
    Yes, it will affect headspace. That's how armorers rebuilt M1 rifles and carbines; they would have a bucket of bolts and try them until the found one that appropriately headspaced. Some bolts are longer than others, and lug wear varies.

    Having said that, you may very well be able to swap bolts with no appreciable change in headspace. It's an experiment.

     
  4. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    I would really question how critical headspace is on the .30 carbine, as long as it is close enough for the extractor to snap over the rim when it chambers the round and fires when you pull the trigger.

    The straight tapered case is not going to stretch & break like a bottle-neck rifle caliber with excess headspace anyway.

    For a quick and dirty test, get yourself a roll of Scotch Magic tape.

    Start applying layers of it to a case head & trimming it even with the rim until the bolt won't close on it all the way.

    Each layer of tape is about .0025" so two layers = .005", etc.

    It should close on one or two layers, and I really doubt four layers, or .010", would hurt anything.

    rc
     
    Last edited: Nov 11, 2010
  5. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,706
    I agree with rcmodel, the combination of low pressure and a straight case greatly reduce headspace concerns with the .30 Carbine. I would just replace the bolt and fire the gun. If there are no signs of trouble, no problem.

    Jim
     
  6. ozmosis

    ozmosis Member

    Joined:
    Jun 8, 2007
    Messages:
    53
    Thank you guys for your help.
     
  7. Mac's Precision

    Mac's Precision Member

    Joined:
    Jul 22, 2010
    Messages:
    301
    Location:
    Bellingham, WA
    Head space on the .30 Carbine should be a non issue. I would bet that you could fire that with .030 and get away with it. I would suspect that misfires due to excess head space would be a bigger issue than pressure problems. Obviously we want to have as little head space as we can but that being said I have seen some rifles with a LOT...and ran fine. Head space issues just aren't as big an issue as some folks assume.

    Cheers
    Mac.
     
  8. Arivacain

    Arivacain Member

    Joined:
    Nov 4, 2012
    Messages:
    1
    Head space in a M1 Carbine

    I have read all the responses but have a question.
    I am not an expert but it seems to me one can simply take of the charging handle spring and slip a live factory round or a non primed resized brass (to be safer) under the extractor and close the bolt.

    If the bolt closes easily and does not rattle or move when you wiggle it with your finger you are good to go.
    I am as always open to other's ideas about this as I recently had a Underwood WW2 bolt crack and bought a new old stock GI bolt for one of my two M1 Carbines and the above is what I did with the trigger assembly off of the gun.
    I am considering buying a field gage for it but money is short right now.
    Thanks
     
  9. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    See post #4, and the later posts by others.

    rc
     
  10. velocette

    velocette Member

    Joined:
    Jan 21, 2008
    Messages:
    689
    Location:
    Ft. Lauderdale Fla
    Remember also that the .30 carbine headspaces on the case mouth like most autoloading pistols. If your bolt has slightly excess headspace, perhaps trimming the cases a little less (longer) can compensate for the added room at the back. That is of course if you are wise enough to reload.

    Roger
     
  11. fguffey

    fguffey Member

    Joined:
    Aug 28, 2008
    Messages:
    2,679
    Practiced by very very few, it is possible to determine the effect the replacement bolt will have on the length of the chamber, a more common practice is order a bucket of bolts then try them one at a time. Problem, no one knows the length of the chamber before they start.

    then there are reloaders with a press with threads, and dies with threads, my presses and dies have threads, threads make my dies in my presses adjustable, I use the length of the case to off set the length of the chamber.

    F. Guffey
     
  12. medalguy

    medalguy Member

    Joined:
    Mar 20, 2009
    Messages:
    3,208
    Location:
    New Mexico
    FWIW, when I was in the Air Force I was an armorer and that was way back when they used M2 carbines. We always stored the rifles in the vault minus bolts for security. Bolts were always tagged with string tags with the SN of the rifle, but when reassembling the bolts to the rifles there were always a few cases where tags came up missing. We always checked headspace before firing them, but to my recollection, we never had a problem with a bolt not functioning properly.

    I'd say put 1-2 thicknesses of tape on a case head, and see if that still allows the bolt to close. 3 thicknesses or more probably should not work. Or, just buy a field gauge from Brownells if it worries you. After checking your headspace, you can sell it on evilbay for about the new cost. Hey, it is new, right?
     
  13. col.lemat

    col.lemat Member

    Joined:
    Apr 3, 2011
    Messages:
    571
    Location:
    Lakewood, Ca
    I never had any problems swapping bolts. The only time I had trouble was with worn locking lugs (.020) on an M2. It was kind of neat as it would blow the primers out, simplified one step when I would reload the brass.
     
  14. lathedog

    lathedog Member

    Joined:
    Aug 28, 2006
    Messages:
    270
    One reason for controlling headspace is to keep the case from moving rearwards under pressure and pounding the bolt face, and causing setback to the bolt lugs. Continued firing with excessive headspace will make the problem grow worse.

    30 Carbine is a ~ 40kpsi cartridge. It is medium pressure compared with modern sporting cartridges, but I would not call it low pressure. It is a tapered case, not straight walled, so will have more bolt thrust than a cartridge with some amount of straight wall sticking to the chamber walls.

    Be careful when you light the fuse on tens of thousands of psi a few inches from your face.
     
  15. carbine85

    carbine85 Member

    Joined:
    Jul 1, 2007
    Messages:
    2,135
    Location:
    Southwest, Ohio
    I have built, rebuilt and re-barreled several carbines. They normally head spaces just fine. I have experienced short chamber space when replacing new Winchester barrels. I have one now that is short and will require a reamer. The carbine head spaces on the end of the cartridge therefore you should check it with a go gauge and a field gauge.
     
  16. justwondering01

    justwondering01 Member

    Joined:
    Nov 11, 2009
    Messages:
    3
    Has anyone replaced a barrel due to head space issues or do you only replace them due to muzzle/rifling wear? A friend has a Postal Meter that recently had a cartridge have the case almost separate and had the primer almost push out. Is this a case of the head space being too large? Would you replace the bolt to solve the problem? Just starting to learn about the M1 Carbine. So any thoughts would be appreciated
     
  17. BBBBill

    BBBBill Member

    Joined:
    Mar 7, 2005
    Messages:
    1,893
    Location:
    Alabama and Florida
    I would not replace anything until I measured the headspace and probably a chamber cast as a minimum. Careful inspection and measurement of the gun using appropriate print specs to verify everything is in spec would be best. Ammo would be suspect, too, until I ruled it out.
     
  18. justwondering01

    justwondering01 Member

    Joined:
    Nov 11, 2009
    Messages:
    3
    How do you do a chamber cast?
     
  19. Canuck-IL

    Canuck-IL Member

    Joined:
    Feb 15, 2005
    Messages:
    1,590
  20. BBBBill

    BBBBill Member

    Joined:
    Mar 7, 2005
    Messages:
    1,893
    Location:
    Alabama and Florida
    Get some cerrosafe from Brownells. Follow the instructions to the letter. Get the headspace gages and the Kuhnhausen book on the service rifles, too.
     
  21. justwondering01

    justwondering01 Member

    Joined:
    Nov 11, 2009
    Messages:
    3
    Thanks for the info!
     
  22. Reloadron
    • Contributing Member

    Reloadron Member

    Joined:
    Jul 6, 2012
    Messages:
    6,949
    Location:
    Cleveland, Ohio USA
    The shop manual BBBBill was kind enough to reference can be found here from Midway.

    Canuck-IL was kind enough to provide a link to chamber casting alloy.

    Forrester headspace gauges from Brownells can be found here.

    The problem is that head space gauges run about $35 EA so if you get a set of three (Go - No Go- Field) you have about $105 in gauges. That plus $32 for the shop manual. Toss in the casting alloy and when all is said and done you have about $150 in tools and gauges.

    The .30 Carbine cartridge while not real strange is not as common as most in how it is head spaced. You may want to give this link a read and scroll down to Head Space. Something else to consider is when checking the head space on a 30 Carbine the rifle is field stripped and then the bolt needs stripped completely removing the firing pin, extractor and the ejector. If you do this watch yourself as things in there are spring loaded and tend to go flying. The bolt is like a miniature M1 Garand bolt in miniature and re assembly can be a challenge without the proper tool. Not impossible, just not fun. The ejector and ejector spring don't always cooperate.

    A Google of "Making a chamber casting" will show you plenty of examples on how it is done. While not a 30 Carbine this video does cover making a chamber casting.

    So the question becomes if you want to make the investment(s) to check a single rifle or take it to a competent smith who is familiar with the 30 carbine and has the right tools to work on one?

    Ron
     
    Last edited: Dec 19, 2012
  23. fguffey

    fguffey Member

    Joined:
    Aug 28, 2008
    Messages:
    2,679
    In 10 words or less, no,

    I'm, if not the only person that knows how to switch out bolts, I am one of a small group that can change a bolt and get it correct every time without a go, no or beyond gage, convincing someone it can be done is another matter. It is helpful when the length of the chamber is to remain the same length, reduced or lengthen.

    On the Internet the advise has always been, purchase a bucket of bolts and start replacing and checking, and hope one of them solves/remedies the problem.

    F. Guffey
     
  24. 345 DeSoto

    345 DeSoto Member

    Joined:
    Jan 5, 2008
    Messages:
    527
    Location:
    Skaneateles,NY Summer/Port St.Lucie,FL Winter
Thread Status:
Not open for further replies.

Share This Page