Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

how much expansion is too much

Discussion in 'Handloading and Reloading' started by lopezni, Aug 6, 2010.

Thread Status:
Not open for further replies.
  1. lopezni

    lopezni member

    Joined:
    Dec 5, 2009
    Messages:
    357
    Location:
    New York
    I have been getting about .003" expansion around the case head area from .472 to .475 after firing a cartridge, is this too much? the cases tend to be harder to reload as they go from first fired to last and the primers start to flatten out, not completely though and no cratering. This is with the same amount of powder in each case. Is this a problem?
     
  2. ranger335v

    ranger335v Member

    Joined:
    Dec 3, 2006
    Messages:
    3,797
    It would be for me.
     
  3. Hondo 60
    • Contributing Member

    Hondo 60 Member

    Joined:
    Sep 6, 2009
    Messages:
    5,381
    Location:
    Manitowoc, WI
    You don't say what caliber, what powder, how much powder, what bullet or the OAL.
    As long as you stay within published loads I wouldn't be too concerned.

    But from what you DID say, it sounds like that's not the case.

    If you're loading them hotter than published data, YES it's a problem.
     
  4. lopezni

    lopezni member

    Joined:
    Dec 5, 2009
    Messages:
    357
    Location:
    New York
    it is 6.5x55 SE and 140gr SPBT 3.050" oal and 43.3 gr RE-22. Well within the limits of the cartridge. This only happens with about 50% of the cases.
     
  5. Ridgerunner665

    Ridgerunner665 Member

    Joined:
    Feb 3, 2005
    Messages:
    3,400
    Location:
    Upper East Tennessee
    It could be that the firearm has a "generously" sized chamber...
     
  6. Robert Wilson

    Robert Wilson Member

    Joined:
    Aug 13, 2009
    Messages:
    402
    Are you using Norma brass? It is often quite soft, in my experience.

    Where you are measuring is also important. If you are measuring just ahead of the web, with a blade micrometer, .003" indicates something is seriously wrong. If that is the situation, I would discontinue all use of the rifle and take it to a gunsmith.

    I suspect, though, that you are measuring some other portion of the case, probably with a standard micrometer or dial caliper, and are seeing the typical expansion one can expect of the lower portion of the case body.

    For what it's worth, I don't consider case head measurements a good gauge of pressure or safety. There is too much disparity between individual rifles and individual brands of brass. Especially now that we have cheap, reliable chronographs, I have given up measuring case heads.
     
  7. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    I agree .003" case head expansion is about .0028 more then you should ever see on any rifle case. That would be measured on the solid part of the case head right in front of the extractor groove.

    However .003" case web expansion is perfectly normal. That would be measured about 1/4"-3/8" foreword of the extractor groove were the case wall has tapered to a much thinner section of the case.
    All that much expansion of the web indicates is a loose chamber.

    .003" case head expansion would indicate a very dangerous over-pressure load and would result in loose primer pockets on the first firing, if not a blow-up.

    rc
     
  8. lopezni

    lopezni member

    Joined:
    Dec 5, 2009
    Messages:
    357
    Location:
    New York
    you're right, the actual "case head" expansion is negligible. where I was noticing the slight bulge was about .215" up from the extractor groove. I only noticed it in about 8 of 15 cases.
     
  9. Innovative

    Innovative Member

    Joined:
    Oct 24, 2009
    Messages:
    286
    Location:
    Florida
    Reading Chamber Pressure ...

    lopenzi .......

    This is a much better indication of chamber pressure from your handloads. The picture shows 4 fired cases that had increasing powder charges. Notice the flatness of the primers. (Picture came from my website.)

    pressure%20signs.jpg
     
  10. Robert Wilson

    Robert Wilson Member

    Joined:
    Aug 13, 2009
    Messages:
    402
    How much pressure was generated by each load?
     
  11. 918v

    918v Member

    Joined:
    Mar 16, 2006
    Messages:
    3,931
    If your case heads expanded .003", your primers would fall out. You are measuring case body expansion, and your numbers are meaningless without a reference to factory ammo using the same brand case.
     
  12. R.W.Dale

    R.W.Dale Member

    Joined:
    Oct 14, 2005
    Messages:
    11,398
    Location:
    Northwest Arkansas
    What brass are you using?

    Domestically made by any chance?

    What does the unfired case head measure?

    Those of you with experience with 6.5x55 will see where this is going

    or undersized brass
     
  13. 918v

    918v Member

    Joined:
    Mar 16, 2006
    Messages:
    3,931
    How about that brass typically expands .003" to seal a chamber?
     
  14. R.W.Dale

    R.W.Dale Member

    Joined:
    Oct 14, 2005
    Messages:
    11,398
    Location:
    Northwest Arkansas
    QUE???
     
  15. 918v

    918v Member

    Joined:
    Mar 16, 2006
    Messages:
    3,931
    He's not measuring the case head.
     
  16. R.W.Dale

    R.W.Dale Member

    Joined:
    Oct 14, 2005
    Messages:
    11,398
    Location:
    Northwest Arkansas
    But we need to know what size the case head IS before firing.

    Here's why

    Domestic 6.5x55 brass makers have gotten lazy (OMG not americans!! ) of late and started making brass with a undersized 473" or 30-06 sized case head rather than the proper .480" case head. this right there could account for the over expansion the OP is noting due to the case being unsupported just north of the case head
     
  17. 918v

    918v Member

    Joined:
    Mar 16, 2006
    Messages:
    3,931
    The OP said the unfired case measures .472" at the expansion ring area, so I figure he must be using domestic brass.

    .003" expansion in this area is prolly OK, but we need a basis for comparison. Being that his chamber is tapered, the more case expansion, the higher the pressure.
     
  18. R.W.Dale

    R.W.Dale Member

    Joined:
    Oct 14, 2005
    Messages:
    11,398
    Location:
    Northwest Arkansas
    Change to a spec case from a european manufacturer and I'll wager the "problem" will absolutely disappear.
     
  19. 918v

    918v Member

    Joined:
    Mar 16, 2006
    Messages:
    3,931
    My question is:

    If his unfired case measures .472" and his fired case measures .475", will a .480" case even chamber?
     
  20. R.W.Dale

    R.W.Dale Member

    Joined:
    Oct 14, 2005
    Messages:
    11,398
    Location:
    Northwest Arkansas
    His cases probably aren't expanding all the way out to the chamber walls just above the case head and are springing back a bit after firing as well.

    If he has a SAAMI or CIP 6.5x55 or 6.5x55skan chamber then a .479/.480" case will fit in there as snug as a bug in a rug and come out after firing looking like a new piece of brass
     
Thread Status:
Not open for further replies.

Share This Page