Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Is the crane easily damaged?

Discussion in 'Handguns: Revolvers' started by ojh, Aug 14, 2003.

Thread Status:
Not open for further replies.
  1. ojh

    ojh Member

    Joined:
    Jun 22, 2003
    Messages:
    137
    Location:
    Finland
    Is the cylinder crane easily damaged by rough or even normal handling?

    The reason I'm asking is this. I bought my first wheelgun a few months ago, and made my decision according advice given in the article "How To Buy A Used Handgun" (in Guns & Ammo 2000 Annual) by Rober T. Shimek. He pays great attention in checking the condition of the crane. He also strongly warns about abusing the crane mechanism. However, he tells that he has accidentally sprung a crane "while handling a revolver in slow-fire and with great care", and also says that "I still do not know how I did the damage!"

    Now I find myself being almost ridiculously cautious with my own piece :uhoh: (it's a stainless King Cobra, 6"). I open and close the cylinder with the utmost care. When someone else handles the gun and slams the cylinder closed, my hair raises and I want to start yelling :cuss: Cleaning the chambers worries me most: it sometimes takes heavy scrubbing, and substantial force and torque is applied to the crane. Would it be better to take the cylinder off for cleaning?
     
  2. J Miller

    J Miller Member

    Joined:
    Dec 25, 2002
    Messages:
    874
    Location:
    Central IL
    ojh,

    Cranes can be damaged. But in over 25 years of shooting double action revolvers, I have never done so.

    I do not baby my revolvers. Nor do I flick my wrist,a la Hollywood, to close the cylinder, or slam them shut.
    I close them with a deliberate motion and start shooting.

    When I clean my revolvers, I always remove the crane from the gun, and pull the cylinder out of it. This makes it much easier to clean the cyinder and the crane.

    S&W's and Colts use one screw on the side of the frame to hold them in.
    I'm not sure about Rugers, and it's been so long since I've had a Dan Wesson I just plain forget.

    I'd quit obsessing about the possible damage and just take reasonable care of your Colt and enjoy it.

    J
     
  3. 4v50 Gary

    4v50 Gary Moderator Staff Member

    Joined:
    Dec 19, 2002
    Messages:
    18,528
    I don't flick my wrist to close the cylinder of any of my revolvers but people have been startled when I yell at them about it. It's such a shocking thing to me and I don't even think twice about moderating my voice. I've never damaged a crane myself but I close the cylinder smartly when I'm shooting for time.
     
  4. dfariswheel

    dfariswheel Member

    Joined:
    Dec 26, 2002
    Messages:
    6,117
    The major problem with damaged cranes was on the old pre-war Colt and S&W revolvers. Colt's especially had rather soft cranes and a drop to the floor, or a couple of "Bogart" slams with a flick of the wrist could bend them.

    The post-war guns have much tougher parts, and the Colt Trooper Mark III/King Cobra revolvers REALLY have tough cranes.

    I won't say you can't bend them, because I have seen some that were, but it takes deliberate abuse to do it.

    With normal use and care you will never spring the crane on a King Cobra.
    They're built like a tank, so don't worry about it.
     
  5. Drifting Fate

    Drifting Fate Member

    Joined:
    Jul 17, 2003
    Messages:
    133
    Location:
    Arizona
    Flicking the wrist to shut the cylinder is the only way I've seen a crane get damaged.

    I won't swear to it, but it seems it probably has to do with the leverge on the crane from overcoming the inertia of the cylinder. I say this because I have, and seen people, be brutal slaming cylinders shut during training by pushing in on the cylinder. No crane damage from that, but take it for what it is worth.
     
  6. Standing Wolf

    Standing Wolf Member in memoriam

    Joined:
    Dec 24, 2002
    Messages:
    24,041
    Location:
    Idahohoho, the jolliest state
    I'd do considerably more than just yell.

    Cranes are pretty sturdy, but can be bent out of alignment by careless handling. I've seen a slightly bent crane or two on used guns in gun shops. Cranes—or "yokes," as they're also called—can be straightened or replaced, but it takes a good gunsmith to do straighten one, and not all replacements are simple replacements.
     
  7. bountyhunter

    bountyhunter member

    Joined:
    Jan 8, 2003
    Messages:
    3,421
    Location:
    Fascist-Fornia
    You can bend a crane if you shoot lead and it builds up on the cylinder face. Then, the cylinder has to be forced back in to get it by the forcing cone and that can bend the crane.
     
  8. ojh

    ojh Member

    Joined:
    Jun 22, 2003
    Messages:
    137
    Location:
    Finland
    Thank you all, again, for sharing your knowledge and experience.

    So, as far as I understand, the bottom lines are: the crane can't be damaged with normal, deliberate handling. Slamming and especially wrist-flipping must be avoided. If the cylinder does not close freely, one should not force it, but see what's wrong. And it's best to take the cylinder off for heavy chamber scrubbing.
     
  9. BluesBear

    BluesBear member

    Joined:
    Jul 25, 2003
    Messages:
    7,672
    Location:
    The Great Pacific NorthWet
    Welcome ojh,

    Seems like you have got it all covered now.

    :)
     
  10. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,566
    A lot of old police guns got bent cranes from sudden contact of the cylinder with the cranium of some recalcitrant individual who didn't understand a previous message concerning his activities.

    Yes, cranes are pretty rugged, but it is worthy of note that both S&W and Colt (I don't know about Ruger) fitted crane and frame before any further finishing was done and before any other parts were installed, and numbered them together. This ensured that those two parts were kept together during the rest of the manufacturing of the gun so the careful fit would be maintained.

    Jim
     
Thread Status:
Not open for further replies.

Share This Page