Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Original Sharps 1863 carbine

Discussion in 'Blackpowder' started by dlon21, Dec 22, 2010.

Thread Status:
Not open for further replies.
  1. dlon21

    dlon21 Member

    Joined:
    Jan 18, 2009
    Messages:
    145
    Location:
    Sweden
    Sometime in the near future I have nice little carbine coming. I need tips about what calibre and type of bullet to use. Was thinking of ordering a mold from Dixie gun works. Think the one they have throws .535 cal bullet, and these guns are .52 right? They also had bullets in different sizes, up to .544 I think. When I have that out of the way, all I need to learn is to make combustible cartridges. So, please tell me all I need to know!
     
  2. arcticap

    arcticap Member

    Joined:
    Mar 20, 2005
    Messages:
    6,185
    Location:
    Central Connecticut
  3. dlon21

    dlon21 Member

    Joined:
    Jan 18, 2009
    Messages:
    145
    Location:
    Sweden
    Thanks Arcticap, I'll check that out if I haven't seen it already.

    - The question is though; what cal. and type of bullet or mold do I need?
     
  4. Mike OTDP

    Mike OTDP Member

    Joined:
    Oct 31, 2007
    Messages:
    1,706
    Location:
    Somewhere in Maryland
    I suggest trying the North-South Skirmish Association at www.n-ssa-org

    They have a much deeper knowledge of the guns.
     
  5. dlon21

    dlon21 Member

    Joined:
    Jan 18, 2009
    Messages:
    145
    Location:
    Sweden
    I've been looking at the n-ssa too a little bit. After reading a little more at dixie gun works, it seems their mold is the correct one.
     
  6. StrawHat

    StrawHat Member

    Joined:
    Jan 28, 2007
    Messages:
    3,623
    Location:
    NE Ohio
    Before ordering anything wait until you can inspect the rifle. Many had oversized bores and to get the best accuracy need a differsnt size bullet. When the Gov't asked Sharps to convert the percussion rifles to cartridge, anything over 52 caliber was sleeved to use the 50-70 cartridge. Anything under 52 caliber was rechambered and fitted with a new block. Lots of variation there.
     
  7. Racebannon

    Racebannon Member

    Joined:
    Feb 20, 2008
    Messages:
    48
    Is it still percussion? My original New Model 1863 was converted by the Army with a three groove barrel liner, and other parts, for the 50-70 cartridge.
     
  8. dlon21

    dlon21 Member

    Joined:
    Jan 18, 2009
    Messages:
    145
    Location:
    Sweden
  9. Racebannon

    Racebannon Member

    Joined:
    Feb 20, 2008
    Messages:
    48
    Very nice! That's percussion all right. I can see why you're interested, it's a beautiful piece.
     
  10. RaiderANV

    RaiderANV Member

    Joined:
    Apr 21, 2008
    Messages:
    54
    Location:
    On me farm in Marshall, Virginny
    Your REALLY gonna want to WAIT until you get the carbine inhand so you can have the bore checked for the EXACT diameter. They varied a lot and it is very important you get not only the correct mold but the correct sizer for the rounds if you expect to hit anything accurately. Your best bet is to visit the N-SSA web site and post under the Shooting Tips& Tricks section as we shoot these in live fire competition and the wealth of knowledge there is unmatched anywhere on the net!

    ====> http://n-ssa.org/phpBB3/

    You can even post the serial number and they'll tell you when/where it was made and maybe even the unit it was issued to during the War of Northern Aggression as it be known in the South! =)

    Hope this helps
    Justin Kelly 7th Virginia Vol Inf.
     
  11. dlon21

    dlon21 Member

    Joined:
    Jan 18, 2009
    Messages:
    145
    Location:
    Sweden
    Okay, I got the gun today. Slugged the barrel and the ball measures in at 13.58 mm, ie .535 inches. The mold at Dixie guns is the same, .535. Is it alright to use a bullet the exact same size as the bore?
     
  12. RaiderANV

    RaiderANV Member

    Joined:
    Apr 21, 2008
    Messages:
    54
    Location:
    On me farm in Marshall, Virginny
    Not really as accuracy will suffer. The problem is just because the mold claims a certain dia. DON'T mean that what it will cast. When the cutting cherry was first made it may have cut the molds at .534 then as it wore up to the point where it was trashed it may have been as high as .539 This is pretty common with all mold makers. It's best to post wanting to buy a mold on a place like the N-SSA as you'll know the exact size of the bullet cast before you buy it.

    There is a mold on Egay right now that should work also. It's a rapine mold that originally sold for $120. It's at $36 now w/ $12 shipping.

    http://cgi.ebay.com/Rapine-Bullet-Mold- ... 19c2298ec8
     
  13. dlon21

    dlon21 Member

    Joined:
    Jan 18, 2009
    Messages:
    145
    Location:
    Sweden
    It's gone.
     
  14. arcticap

    arcticap Member

    Joined:
    Mar 20, 2005
    Messages:
    6,185
    Location:
    Central Connecticut
    Just because someone else claimed how it had cast for them, due to the different alloys that folks use, one can never know what the actual bullet size will be for a used mold.
    However, new Lee molds are known for being very precise and a sizing die isn't very expensive if the bullet diameter was an issue.
     
    Last edited: Jan 8, 2011
  15. Jim Watson

    Jim Watson Member

    Joined:
    Dec 24, 2002
    Messages:
    22,340
  16. dlon21

    dlon21 Member

    Joined:
    Jan 18, 2009
    Messages:
    145
    Location:
    Sweden
    Thanks, I'll link this thread at that forum.
     
  17. RaiderANV

    RaiderANV Member

    Joined:
    Apr 21, 2008
    Messages:
    54
    Location:
    On me farm in Marshall, Virginny
Thread Status:
Not open for further replies.

Share This Page